Bedienungsanleitung Parkside IAN 56052 PFBS 9.6 A1 (Seite 56 von 75) (Englisch, Portugiesisch, Spanisch)

744906

Zoom out

Zoom in

Vorherige Seite

1/75

Nächste Seite

56 GB/MT

J Always keep the device

clean, dry and free of oil or grease.

J Children or persons who lack the knowledge or

experience to use the device or whose physical,

sensory or intellectual capacities are limited

must never be allowed to use the device without

supervision or instruction by a person responsi-

ble for their safety. Children must never be

allowed to play with the device.

Operation

Never use the device for a purpose for which it was

not intended or with non-original parts / accessories.

The use of tools or accessories other than those rec-

ommended in the operating instructions could lead

to you suﬀering an injury.

Charging the battery pack

NOTE! A battery pack that has been

unused for a while or never been charged

must be charged before reuse or ﬁrst use.

The battery pack requires about 3-5 cycles before

it can reach its full charge. The charging process

takes about 180 minutes.

CAUTION! RISK OF INJURY!

Always pull

out the mains plug (

mains adapter

) before

you

insert the battery pack into or take it out of

the charger.

j Connect the adapter

to a mains socket.

j Insert the battery pack

3 a

into the charging

cradle

. This can only be inserted with the

correct polarity.

j The LED

lights up green whenever the bat-

tery pack

3 a

is in the charging cradle

and

the adapter

is connected to a mains socket.

CAUTION! Do not charge a battery pack for

a second time in close succession. There is a

danger of overcharging the battery pack.

Inserting / removing the

battery pack into / out of the

drill / grinder

Inserting the battery pack:

j Set the ON / OFF switch

to position “0”.

j Insert the battery pack

3 a

into the drill / grinder

until it engages.

Removing the battery pack:

j Pressing the battery pack buttons

at the

sides at the same time allows you to remove

the battery pack

3 a

Reading oﬀ the battery status

The status or residual power is indicated as follows

in the battery-operated LED

whenever the appli-

ance is switched on:

RED / ORANGE / GREEN = maximum charge / power

RED / ORANGE = medium-level charge / power

RED = weak charge – recharge battery

Inserting or replacing

a tool / collet

j Press the spindle lock

and keep it pressed.

j Rotate the clamping nut

until the lock

engages.

j Loosen the clamping nut

with the combina-

tion key

j If a tool is already inserted, remove it.

j First insert the tool you wish to use through the

clamping nut

before you insert it into the

collet

suitable for the tool shaft.

j Press the spindle lock

and keep it pressed.

j Insert the collet

into the threaded insert and

tighten the clamping nut

on the thread using

the combination key

NOTE: Use the screwdriver end of the combi-

nation key

to release or tighten the screw of

the mandrels

General safety advice for electrical power tools / Operation

56052_par_Akku-Multischleifmaschine PFBS 9.6 A1_content_LB5.indd 56 21.04.11 13:22

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 56052 PFBS 9.6 A1 Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 56052 PFBS 9.6 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info