Bedienungsanleitung Parkside IAN 56294 PTS 450 A1 (Seite 41 von 55) (Englisch, Portugiesisch, Spanisch)

744925

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

41 GB/MT

Note: Do not use grinding discs. Failure to observe

this advice may result in injury or damage.

To avoid danger to life

from electric shock:

Frequently check the condition of

the device, mains lead and plug.

Do not use the device if these kinds

of parts

are damaged. Never open up the device.

damaged device, mains lead or plug presents

a serious danger to life from electric shock. Al-

ways have any repairs carried out or replacement

parts ﬁtted at the service centre or by an elec-

trical equipment repair specialist.

J Do not operate the device if it is damp and do

not use it in a damp environment.

J If you use the device outdoors, always connect

it through a residual current device (RCD) with

a maximum trip current of 30 mA. If using an

extension lead, always use one that is approved

for outdoor use.

Note: Always keep the mains lead away from the

working area of the machine and lead away the

mains lead from the rear.

Preparation for use

Switching on and oﬀ

Switching on:

j Pull the ON / OFF switch

back (see Fig. A).

Switching off:

j Release the ON / OFF switch

Releasing the plunge stop

j Press the plunge stop

forward and keep it

pressed.

Setting the cutting depth

Note: If possible we recommend that the cutting

depth is set approximately 2 mm greater than the

material thickness. This should help to ensure you

achieve a clean cut.

j Unclamp the quick-release lever of the cutting

depth setting clamp

, set the required cutting

depth on the scale

8 a

and reclamp the quick-

release lever.

Setting the guide fence

j Release the wing screw for the guide fence

11 a

on the base plate

and set the guide fence

in the guide fence slot

. Retighten the wing

screw for the guide fence

11 a

Handling the plunge saw

1. Place the device on the workpiece and switch

it on as described in the section on “Switching

on and oﬀ”.

2. If necessary, align the saw with the guide fence

or on a marked line.

3. Hold the device as shown in Fig. A and saw

using the appropriate amount of pressure.

Saw blade types:

The supplied saw blade types cover the most com-

mon ﬁelds of application.

Saw blade with hardened metal teeth

Z85 / 30:

Description: ø 85 mm, 30 hardened metal teeth

Suitable for: Softwood, hardwood, boards of all type

Diamond saw blade

Z85VR:

Description: ø 85 mm non-segmented blade

Suitable for: Ceramic, plastic

HSS saw blade

Z85 / 36:

Description: ø 85 mm, 36 teeth – left / right side set

Suitable for: Softwood, hardwood, boards of all

type, quick cut

General safety advice for electrical power tools / Preparation for use

56294_par_Tauchsaege_Content_LB5.indd 41 27.04.11 13:12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 56294 PTS 450 A1 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 56294 PTS 450 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info