Bedienungsanleitung Parkside IAN 61094 PBSG 55 A1 (Seite 33 von 45) (Englisch, Portugiesisch, Spanisch)

744938

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

33 GB/MT

out the mains plug. This prevents the grinder restar

ing by accident, which could cause injury to you.

 Never operate the grinder if the power

cable or mains plug is damaged.

 Grinding stones must be carefully

stored and handled according to the

manufacturer’s instructions.

 Make sure that the grinding tools are

appropriate in line with the instructions

of the manufacturer.

 Check the grinding stone before using

it; do not use any broken, cracked or otherwise

damaged goods.



Make sure that a grinding tool is correct-

ly fitted and fastened before using it.

Place the grinder in a safe place and allow it

to run idly for 30 seconds. Stop it immediately if

considerable oscillations occur or if defects are

observed. If this occurs, check the machine to

ﬁnd out the cause.



Original accessories /

Attachments



Use only the accessories and attachments

detailed in the operating instructions.

The use of inserted tools or accessories other

than those recommended in the operating in-

structions could lead to you suﬀering an injury.



Use



Sharpening a drill

NOTE: Badly damaged drills should ﬁrst be coarsely

sharpened on a sharpening block.

 Fully lower the sharpening stone. To do this turn

the rotary switch

in the DOWN direction

as far as it will go.

 Insert the drill into the smallest suitable drill

guide

on the drill sharpener. The exact size

(Ø) of each drill guide

is shown by the ad-

jacent lettering (3 to 10).

 Press the ON / OFF switch

into position “I”

to switch on the device.

 Turn the rotary switch

in the UP direction

until you hear a grinding noise.

NOTE: The rotary switch

controls the posi-

tion of the sharpening stone in the sharpening

head housing and therefore the pressure of the

sharpening stone against the drill. The further

you turn the rotary switch

in the UP di-

rection, the greater the pressure. Ensure that

you do not turn the sharpening stone too far up.

Otherwise the sharpening stone could strike

the housing.

 Turn the drill under slight pressure loosely and

quickly to and fro between the left and right

stops about 10 times (with small drills about

5 times).

 Pull the drill out, turn it through 180° (horizon

tally)

and insert it again until it meets the sharpening

stone.

 If necessary repeat whole process until both

cutting edges of the drill are sharp. Control the

grinding operation so that the angle between

the main and transverse cutting edges for a

standard drill is 130°. Both cutting edges (b)

must have the same angle to the drill axis (a)

and be the same length so that the drill runs

concentrically (see following ﬁgures).

(b)(b)

(a)

 Press the ON / OFF switch

into position “0”

to switch oﬀ the device.



Replacing the

sharpening stone

RISK OF INJURY! Before you

carry out any work on the device, always pull the

mains plug out of the mains socket. Replace the

sharpening stone if it is worn out or damaged

(deteriorating, irregular sharpening performance,

General safety advice / Use

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 61094 PBSG 55 A1 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 61094 PBSG 55 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info