Bedienungsanleitung Parkside IAN 63964 PFS 100 B2 (Seite 39 von 54) (Englisch, Portugiesisch, Spanisch)

744904

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

39 GB/MT

and advice. Electrical power tools are dan-

gerous when they are used by inexperienced

people.

Look after the device carefully. Check

that moving parts are working prop-

erly and move freely. Check for any

parts that are broken or damaged

enough to detrimentally affect the

functioning of the device. Have dam-

aged parts repaired before you use

the device. Many accidents have their origins

in poorly maintained electrical power tools.

f) Use the electrical power tool, accesso-

ries, inserted tools etc. in accordance

with these instructions and advice, and

the stipulations drawn up for this par-

ticular type of device. In doing this, take

into account the working conditions

and the task in hand. The use of electrical

power tools for purposes other than those in-

tended can lead to dangerous situations.

Additional safety advice

for paint spray guns

 The spray gun must never be used for

spraying inflammable substances.

Spray guns must never be cleaned

using inflammable solvents.

 If you do not know the level of danger

a substance presents, do not spray it.

 Precise observation of the hazard

warnings, information and data

sheets available from the sprayed

medium manufacturer is essential.



Wear a breathing / dust mask!

The inhalation of paint mist and sol-

vent vapour is hazardous to health.

 Work in adequately ventilated

spaces only.



Wear protective glasses!

 Never aim the spray at living

creatures.

 DANGER OF EXPLOSION! Do

not use the device in environments

containing gases, open ﬂames, ﬁres

or gas-operated water heaters.



NO SMOKING!

 Paint and solvents (thinners) must

have a flashpoint above 21°C.



Advice on use



DIN-sec / Viscosity

The Parkside paint spray gun PFS 100 B2 can be

used to apply sprayed media with a viscosity up to

80 DIN-sec. Viscosity is determined in a simpliﬁed

measuring procedure using the supplied measuring

cup (see Fig. C).

1. Immerse and ﬁll the supplied measuring cup

to the top with the medium to be sprayed.

2. Lift the measuring cup

out of the medium

to be sprayed and let the liquid ﬂow out (see

Figure C).

3. Measure the time in seconds it takes for the

ﬂow of liquid out of the measuring cup to cease.

This time is the “DIN-seconds (DIN-s)” value of

viscosity.

4. If the value is too high, incrementally add and

mix in small quantities of a thinner compatible

with the medium to be sprayed. Proceed in ac-

cordance with the section about “Preparing the

sprayed medium”.

5. Remeasure the DIN-seconds value.

Repeat this procedure until a value is obtained

that complies with the values in the table.



Preparing the sprayed medium

NOTE: Most paints, varnishes etc. in the shops

are intended to be applied by brush not spray. To

achieve the best spraying result, you should prepare

your paint or varnish etc. in accordance with DIN

guidelines to achieve a suitable viscosity (see table).

General safety advice for electrical power tools / Advice on use

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 63964 PFS 100 B2 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 63964 PFS 100 B2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info