Bedienungsanleitung Parkside IAN 66445 PMGS 12 A1 (Seite 53 von 70) (Englisch, Portugiesisch, Spanisch)

744927

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

53 GB/MT

Avoid contact with moving sanding or

grinding tools.

DANGER OF FIRE FROM FLYING

SPARKS! Abrading metal creates

ﬂying sparks. For this reason, always

make sure that nobody is placed in any danger

and that there are no inﬂammable materials

near the working area.

DUST HAZARD! Any

harmful / noxious dusts generated from machin-

ing represent a risk to the health of the person

operating the device and to anyone near the

work area.

Wear a dust mask!

NOXIOUS FUMES!

Ensure that there is adequate ventilation when

machining surfaces containing plastic or cov-

ered with paint, varnish etc.

Do not soak the materials or the sur-

face you are about to work on with

liquids containing solvents.

Avoid abrading paints containing lead

or other substances hazardous to

health.

Do not machine materials containing

asbestos. Asbestos is a known carcinogen.

Do not machine moist materials or

damp surfaces.

NOTE! Do not allow the tool to come to a

standstill by overloading it!

Switch the device off

and allow it to come to a standstill be-

fore you put it down.

Always keep the de

vice

clean, dry and free of oil or grease.

Children or persons who lack the knowledge or

experience to use the device or whose physical,

sensory or intellectual capacities are limited

must never be allowed to use the device without

supervision or instruction by a person responsible

for their safety. Children must never be allowed

to play with the device.

Operation

Never use the device for a purpose

for which it was not intended or with

non-original parts / accessories. The use

of tools or accessories other than those recom-

mended in the operating instructions could lead

to you suﬀering an injury.

Inserting or replacing

a tool / collet

Press the spindle lock

and keep it pressed.

Rotate the clamping nut

until the lock

engages.

Loosen the clamping nut

with the combina-

tion key

If a tool is already inserted, remove it.

First insert the tool you wish to use though the

clamping nut

before you insert it into the

collet

suitable for the tool shaft.

Press the spindle lock

and keep it pressed.

Insert the collet

into the threaded insert and

tighten the clamping nut

on the thread using

the combination key

Using the Insertion tool with mandrel

NOTE: Use the screwdriver end of the combi-

nation key

to release or tighten the screw of

the mandrels

Insert the mandrel

into the electrical tool as

described.

With the aid of the combination wrench

unscrew the screw from the mandrel

Place the insertion tool you wish to have onto

the screw between the two washers.

With the aid of the combination wrench

tighten the screw on the mandrel

Switching on and oﬀ /

Setting the speed range

Switching on / Setting the speed range:

Connect the plug

to the power supply unit

by inserting it into the plug-in device

provided

for such purposes (see Fig. C).

General safety advice for electrical power tools / Operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 66445 PMGS 12 A1 Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 66445 PMGS 12 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info