Bedienungsanleitung Parkside IAN 66765 PABS 18 Li B2 (Seite 47 von 62) (Englisch, Portugiesisch, Spanisch)

744908

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

47 GB/MT

3. The green charging control LED

signals to

you that the charging process is complete and

the battery pack

is ready for service.

Never charge the battery pack for a second time

immediately after a fast charging process has

been completed. This can give rise to the battery

pack becoming overcharged and to a reduced

service life of the battery and charging station.

Switch the charger oﬀ for at least 15 minutes

between two successive charging procedures.

Remove the power plug from the wall socket.

Insertion / removal of a battery

pack into the appliance

Ensure that the appliance is switched oﬀ before in-

serting the battery. The insertion of a battery into an

electrical appliance that is switched on can lead to

accidents.

Inserting the rechargeable battery pack:

Move the rotation switch

into the middle

position (lock) and push the rechargeable bat-

tery pack

into the handle until it engages.

Removing the rechargeable battery pack:

Press the release button

and remove the

rechargeable battery pack

Checking battery status

To check the battery status, press the battery

LED button

(refer to main diagram). The

status or residual capacity will be indicated in

the battery LED

as follows:

GREEN / RED / ORANGE = maximum charge /

capacity

RED / ORANGE = medium charge / capacity

RED = weak charge – recharge battery

Changing tools

Your cordless electric drill / screwdriver has a fully

automatic spindle lock

and is ﬁtted with an

enclosed keyless chuck incorporating the latest

technology from

”Made in Germany”.

Once the motor has come to a halt, the drive shaft

is automatically locked, so that the chuck

can

be opened simply by turning it

After you have inserted the required bit and ﬁxed it

in place by turning the chuck

, you can immedi-

ately continue working. The spindle lock releases

itself automatically when the motor is started (by

operation of the ON / OFF switch

Torque pre-selection

You can adjust the torque by using

torque pre-

selection. The torque levels regulate a range of up

to ca. 35 Nm.

Select a low setting for small screws, soft work

material.

Select a high setting for large screws, hard

work materials and for the extraction of screws.

For drilling, push the selector to the setting for

drilling, in that you adjust the torque pre-selector

to the position

For drilling tasks, also push the gear selector

switch

to the front (Position: 2).

2 Gear Drive

CAUTION! Move the gear selector switch

only after the device has come to a standstill.

Failure to observe this advice may result in damage

to the device.

In the ﬁrst gear (Gear selector switch

in Position: 1)

A speed of up to approx. 400 rpm can be achieved

and a high torque. This setting is intended for use w

ith

all screwing tasks and for accessories (see example

Fig. B).

In the second gear (Gear selector switch

in Position: 2)

It achieves a speed of up to approx. 1400 rpm, for

the carrying out of drilling tasks (see example Fig. A).

Before first useGeneral safety advice for electrical power tools / Before first use

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 66765 PABS 18 Li B2 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 66765 PABS 18 Li B2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info