Bedienungsanleitung Parkside IAN 68917 PBS 900 A1 (Seite 40 von 55) (Englisch, Portugiesisch, Spanisch)

744911

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

40 GB/MT

Preparing for use

Tensioning / changing

the sanding belt

RISK OF INJURY! Before

you carry out any work on the belt sander always

pull the plug out of the mains socket.

1. Then release the tensioner for the sanding belt

by moving the tensioning lever

fully out-

wards (see ﬁg. A). The tensioner is now open

and the sanding belt can be removed.

2. Next insert a new sanding belt or change the

belt for one suitable for a diﬀerent material or

one with a diﬀerent grit size.

IMPORTANT: The direction of the arrows on

the inside of the sanding belt must agree with

that on sander housing.

3. Press the tensioning lever

back into its

initial position.

Adjusting the sanding belt:

Pick up the device, switch it on and turn it over.

Adjust the belt tracking by turning the adjuster

screw

until the edge of the sanding belt is

ﬂush with and runs parallel to the edge of the

device (Fig. B.).

IMPORTANT: Always make sure that the

sanding belt does not cut into the housing.

Check the sanding belt regularly and if neces-

sary re-adjust it using the adjuster screw

Advice on use

Light sanding pressure is enough:

Apply light sanding pressure only. The weight

of the belt sander alone is adequate to pro-

duce good sanding results. By adopting this

approach you will also prolong the life of your

sanding belts and obtain a smoother work-

piece surface.

Sanding and surfaces:

The sanding output and the quality of the surface

ﬁnish obtained are determined by the belt speed

and the grade of grit on the sanding belt (see the

section on “Selecting the correct rotational speed

and sanding belt”).

Sanding procedure:

With the sander switched on, bring it into con-

tact with the workpiece and move it forward

carefully. Work in parallel and overlapping

widths. Always work in the direction of the grain

to avoid undesirable transverse sanding marks.

After sanding always lift the device from the

workpiece before switching it oﬀ.

Vacuum dust extraction

DANGER OF FIRE! There is

the danger of ﬁre when working with electrical de-

vices that have a dustbox or can be connected to a

vacuum cleaner. Under certain conditions the

wood dust in the dust collection box (or in the vacu-

um‘s dust bag) may self-ignite, e.g. as a result of

ﬂying sparks generated when abrading metals or

metal objects left in wood. This can happen partic-

ularly if the wood dust is mixed with paint residue

or other chemicals and the abraded particles are

hot from prolonged abrasion. Therefore you must

empty the device’s dust collection box and the vac-

uum cleaner’s dust bag before taking a break or

stopping work and always avoid overheating of the

abraded particles and the device.

Wear a dust mask!

Dust extraction using the dust

collection box:

Slide the dust collection box

on to the dust

extraction spout

on the side of the device

(Fig. C).

Emptying the dust collection box:

Pull the dust collection box

oﬀ the dust

extraction spout

. Open the dust collection

box

and empty it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 68917 PBS 900 A1 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 68917 PBS 900 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info