Bedienungsanleitung Parkside IAN 73790 PDMH 4500 A2 (Seite 44 von 50) (Deutsch, Englisch, Holländisch, Französisch)

745068

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

- 44 -

Residual risks

Even if you use the equipment in ac-

cordance with the instructions, certain

residual risks cannot be eliminated. The

following hazards may arise in connec-

tion with the equipment’s construction

and layout:

1. Lung damage if no suitable protective dust

mask is used.

2. Damage to hearing if no suitable ear protec-

tion is used.

3. Health damage caused by hand-arm vib-

rations if the equipment is used over a pro-

longed period or is not properly guided and

maintained.

Air supply:

Via a compressed air source with pressure setting

function, e.g. a compressor. Before starting up,

please also read section 7 “Care and mainte-

nance”.

Performance values of the compressor:

The compressor used should have a tank volume

of at least 50 liters and a motor rating of approx.

2.2 kW.

Setting values for work with the suction

spray gun:

Set a maximum working pressure of 6.3 bar at

your compressed air supply.

6. Before starting the

equipment

Fig. 3

Screw the supplied nipple (4) into the air connec-

tion after you have wound 2-3 layers of sealing

tape around the thread. Plug the required chisel

into the hexagon mount of the chisel hammer. Slip

the tensioning spring (5) over the chisel. Turn the

tensioning spring onto the thread of the cylinder

(1) as far as the stop. As you do this, hold the ten-

sioning spring by the front arm.

Connect the chisel hammer to a compressor or

compressed air network with matching power. Do

this with a ﬂ exible compressed air hose

(Ø 10 mm internal) with quick-lock coupling.

Make sure that the air regulation screw (3) is

adjusted so that air can ﬂ ow through. Move the

chisel hammer towards the object you want to

work on. Actuate the trigger lever (2) to start the

chisel hammer.

Check the equipment and the mounted tool each

time before use. This also includes checking the

speed and the level of vibrations.

To change the chisel you must ﬁ rst disconnect the

equipment from the compressed air source. Turn

the tensioning spring off the cylinder of the chisel

hammer by holding it by its rear arm. The chisel

can now be changed as described above.

The chisel shaft should be lubricated with a little

normal lubricating grease from time to time.

7. Maintenance and care

Important: Disconnect the equipment from the

compressed air supply before you carry out any

maintenance or cleaning work.

Compliance with the maintenance instructions lis-

ted here will help this quality product provide you

with a long service life and trouble-free operation.

Clean the equipment thoroughly and immediately

each time after it has been used.

Regular lubrication is essential for your chisel

hammer to work properly for a prolonged peri-

od of time. Use only special compressed air oil

as supplied. Special compressed air oil is also

available from your dealer.

Note: Use environmentally friendly compressed

air oil if you want to operate the equipment out-

side the workshop.

Anleitung_4139031_LB2.indb 44Anleitung_4139031_LB2.indb 44 03.04.12 10:1403.04.12 10:14

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 73790 PDMH 4500 A2 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info