Bedienungsanleitung Parkside IAN 75273 PMGS 12 B2 (Seite 40 von 45) (Deutsch, Englisch, Holländisch)

745064

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

40 GB

Further special safety

advice for disc-cutting

a) Avoid snagging the cutting disc and

do not use too much contact pressure.

Do not attempt to make excessively

deep cuts. Overloading the cutting disc in-

creases the load and the tendency of the disc

to twist or snag in the cut, making kickback or

disc breakage more likely.

b) Avoid the area in front of or behind

the rotating cutting disc. If the cutting disc

is moving away from you at the point of con-

straint in the workpiece, then, in the event of

a kickback, the electrical power tool and the

rotating disc may be thrown towards you.

c) If the cutting disc jams or you stop

work for a while, switch the device

off and hold it until the disc comes to

a complete stop. Never attempt to

pull the still rotating cutting disc out of

the cut as this could cause kickback.

Determine and rectify the reason for the jamming.

d) Do not switch on the device if the cut-

ting disc is in the workpiece. Allow

the cutting disc to reach full speed be-

fore carefully continuing with the cut.

Otherwise the disc could snag, jump out of the

workpiece or cause a kickback.

e) Support boards or workpieces whilst

cutting to reduce the risk of kickback

caused by a jammed cutting disc. Large

workpieces may bend under their own weight.

The workpiece must be supported to both sides

of the cutting disc and particularly near the

cutting disc and at the workpiece edge.

f) B

e particularly careful when pocket

cutting in existing walls or other areas

where you cannot see what you are cut-

ing into. The cutting disc plunged into the surface

could cut through gas or water pipes, electricity

cables or other objects and cause kickback.

Special safety advice for

abrading using sandpaper

Do not use over-sized sanding sheets.

Follow the manufacturer’s recommen-

dations for sanding sheet size. Sanding

sheets that project beyond the backing pad

could cause injury in addition to jamming,

tearing of the sheet or kickback.

Special safety

advice for polishing

Do not use the polishing bonnet if it

has any loose parts, in particular the

fastening cords. Tuck the fastening cords

away or trim them. Loose fastening cords rotat-

ing with the attachment could catch your ﬁngers

or become trapped in the workpiece.

Special safety advice for

working with wire brushes

a) Bear in mind that wire brushes lose

pieces of wire during normal use. Do

not overload the wires by applying too

much pressure. Flying pieces of wire can very

easily penetrate thin clothing and / or skin.

b) U

se a guard, if recommended, but m

ake

sure that the wire brush does not come

into contact with the guard. The diameters

of disc brushes and cup brushes can increase

due to contact pressure and centripetal forces.

Device-speciﬁc safety

instructions for small drill

PMGS 12 B2 and mains

adapter-PMGS 12 B2-1

When you use the drill /

grinder wear the following

protective equipment: safety glasses

and protective gloves.

General safety advice for electrical power tools General safety advice for electrical power tools / Operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 75273 PMGS 12 B2 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 75273 PMGS 12 B2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info