Bedienungsanleitung Parkside IAN 79191 PWS 125 A1 (Seite 60 von 67) (Französisch, Italienisch)

745099

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

60 GB

General safety advice for electrical power toolsGeneral safety advice for electrical power tools

d) Do not switch on the device if the cut-

ting disc is in the workpiece. Allow

the cutting disc to reach full speed be-

fore carefully continuing with the cut.

Otherwise the disc could snag, jump out of the

workpiece or cause a kickback.

e) Support boards or workpieces whilst

cutting to reduce the risk of kickback

caused by a jammed cutting disc. Large

workpieces may bend under their own weight.

The workpiece must be supported to both sides

of the cutting disc and particularly near the

cutting disc and at the workpiece edge.

f) B

e particularly careful when pocket

cutting in existing walls or other areas

where you cannot see what you are cut-

ing into. The cutting disc plunged into the surface

could cut through gas or water pipes, electricity

cables or other objects and cause kickback.

Special safety advice for

abrading using sandpaper

Do not use over-sized sanding sheets.

Follow the manufacturer’s recommen-

dations for sanding sheet size. Sanding

sheets that project beyond the backing pad

could cause injury in addition to jamming,

tearing of the sheet or kickback.

Special safety

advice for polishing

Do not use the polishing bonnet if it

has any loose parts, in particular the

fastening cords. Tuck the fastening cords

away or trim them. Loose fastening cords rotat-

ing with the attachment could catch your ﬁngers

or become trapped in the workpiece.

Special safety advice for

working with wire brushes

a) Bear in mind that wire brushes lose

pieces of wire during normal use. Do

not overload the wires by applying too

much pressure. Flying pieces of wire can very

easily penetrate thin clothing and / or skin.

b) U

se a guard, if recommended, but m

ake

sure that the wire brush does not come

into contact with the guard. The diameters

of disc brushes and cup brushes can increase

due to contact pressure and centripetal forces.

Safety advice

for angle grinders

DANGER OF ELECTRIC SHOCK! Do not

operate the device if the mains lead

or mains plug is damaged.

DANGER OF ELECTRIC SHOCK! Do not

touch the mains lead if it becomes

damaged or cut through while you

are using the device. Pull the plug out of

the mains socket immediately and have the de-

vice repaired by a suitably qualiﬁed person or

at your service centre.

DANGER OF ELECTRIC SHOCK! Do not

operate the device if it is damp and

do not use it in a damp environment.

DANGER OF ELECTRIC SHOCK! If you

use the device outdoors, always con

nect

it through a residual current device

(RCD) with a maximum trip current of

30 mA. If using an extension lead, always use

one that is approved for outdoor use.

Do not suspend or carry the device by

the mains lead. Always work with the

mains lead leading away from the

rear of the device. Otherwise the device

could be damaged.

Grinding discs must be carefully kept

and handled in accordance with the

manufacturer’s instructions. Otherwise

they could be damaged.

Make sure that abrasive consumables

and tools are attached in accordance

with the manufacturer’s instructions

and advice. Otherwise they could become

detached from the device and result in injury

and / or damage to property.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 79191 PWS 125 A1 Seite 60

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 79191 PWS 125 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info