Bedienungsanleitung Parkside IAN 79192 PEH 30 A1 (Seite 41 von 45) (Deutsch, Englisch, Holländisch, Französisch)

745091

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

41 GB

Preparing for useGeneral safety advice for electrical power tools / Preparing for use

Push the planing debris removal port

into

the device.

Lock the planing debris removal port

turning it into the “Lock” position.

External vacuum extraction:

If necessary ﬁt the reducer piece

when using

a dust extraction system, e.g. a workshop dust

extraction system.

The vacuum cleaner / dust extraction device used

must be suitable for the material being planed.

Connection:

Place the reducer piece

ﬁrmly on to the

planing debris removal port

Push the hose of a suitable dust extraction device

approved for that purpose (e.g. a workshop

vacuum cleaner) on to the planing debris remov-

al port

or the reducer piece

Removal:

Pull the hose of the dust extraction device oﬀ

the planing debris removal port

or oﬀ the

reducer piece

Pull oﬀ the reducer piece

, if ﬁtted.

Parking shoe (see Figs. B / C)

The parking shoe

allows you to lay the device

down without the risk of damaging the workpiece.

When planing, the parking shoe

swings up and

exposes the rear part of the sole

The planing process

CAUTION! DANGER OF KICKBACK!

Always switch on the device before placing it

against the workpiece.

Set the required cutting depth.

Switch on the device.

Always place the front part of the sole

down

ﬁrst on to the workpiece.

Guide the device with even forward movement

over the surface being planed.

Move the device forward at a slow rate and

ensure that the contact pressure acts evenly on

the sole

. Moving forward at too great a rate

results in a poorer surface quality and can lead

to blocking of the planing debris removal port.

Chamfering edges (see Fig. H)

The V-grooves

in the front sole

allow the de

vice

to be used for simple chamfering of workpiece edges.

Use the V-groove most appropriate to your

desired chamfer width.

Place the planer with the V-groove

on the

work-

piece edge and guide the planer along the edge.

Using the guide fence (see Fig. I)

Attach the guide fence

to the device with

the ﬁxing screw

Release the ﬁxing nut

and set the guide at

the desired distance.

Retighten the ﬁxing nut

Exert some slight sideways pressure when guid-

ing the planer with the guide fence.

Using the rebate depth stop

(see Fig. J)

Attach the rebate depth stop

to the device

with the ﬁxing screw

Set the desired rebate depth with the rebate

depth stop

Make the required number of passes with the

planer until desired rebate depth is achieved.

Removing and installing a

planer blade

(see Fig. D)

DANGER OF INJURY!

Before you carry out any work on the device always

pull the mains plug out of the mains socket.

CAUTION! The sharp cutting edges of the plan-

er blade

present an injury hazard! Never

touch the cutting edges of the planer blade

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 79192 PEH 30 A1 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info