Bedienungsanleitung Parkside IAN 86585 PHLG 2000 B1 (Seite 33 von 36) (Deutsch, Englisch, Holländisch, Französisch)

745106

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

33 GB

using the device, always pull the mains plug

out of the mains socket.

Do not direct the device at the same spot for

too long a period.

Maintain a distance between the jet outlet

nozzle and the workpiece or the surface being

heated. An air blockage could lead to over-

heating of the appliance.

Pay heed to the direct working area and also

to its surroundings. The heat produced could

reach to inﬂammable articles located out of the

visible area.

Always keep the device clean, dry and free

of oil or grease.

Never use the device for a purpose for which it

was not intended.

Operation

Preparing the device for use

CAUTION! When using the device, never

allow the ventilation slots to be covered.

CAUTION! DANGER OF BURNS! Do not

touch the hot nozzle.

Switching on the device:

Press the ON / OFF switch

into setting “I“

or “II“.

Switching off the device:

Press the ON / OFF switch

into setting “0“.

Adjusting the air quantity and temperature:

You can use the temperature and air quantity control

to set two diﬀerent blower levels. It is therefore

possible to select the appropriate quantity of air and

temperature in accordance with the intended use:

Setting I 300 l / min 350 °C

Setting II 500 l / min 550 °C

Use as free-standing unit / during

cooling (see Fig. D):

Always set the device down upright on

a level surface, this will allow

· you to have both hands free

· the device to cool

Changing the nozzle

Too much heat causes paints

and plastics to ignite.

CAUTION! Do not inhale the resulting vapours.

Protector nozzle

– for removing paint

and varnish (see Ill. B):

Place the protector nozzle

on the

outlet tube

The spatula shape of the nozzle ensures the air

is properly directed. Use a separate spatula for

removing paint or varnish.

Flat nozzle

– for detaching glues,

softening paint (see Ill. C):

Place the ﬂat nozzle

on the outlet tube

Do not apply heat for too long a period, as

burnt paint becomes much more diﬃcult to

remove. Many glues can be softened by warm-

ing. Glued connections can then be detached

and excess glue removed.

Reducing nozzle

– for welding plastic:

Place the reducer nozzle

on the

outlet tube

Use the reducing nozzle

for heat-shrinkable

sleeves and ﬁlm.

Further examples of uses in

the house, car and garden

Defrosting water pipes:

Notice! It must not be used for thawing PVC pipes.

Notice! It is often very diﬃcult to tell the diﬀerence

between gas pipes and water pipes. If in doubt, ask

a competent person.

Notice! Copper pipes are joined using tin solder

and must not be heated above 200 °C.

General safety advice for electrical power tools / OperationGeneral safety advice for electrical power tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 86585 PHLG 2000 B1 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info