Bedienungsanleitung Parkside IAN 86735 PASS 3.6 A1 (Seite 55 von 62) (Deutsch, Englisch, Holländisch, Französisch)

745079

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

- 55 -

6. Before starting the

equipment

 Caution:

Be sure to read the following information before

you use your cordless screwdriver for the ﬁ rst time:

1. Only charge the battery pack using the char-

ger (11) supplied.

2. Only use screwdriver bits which are in perfect

working order and appropriate.

3. When screwing into walls or partitions, test

these for electrical, gas or water connections.

7. Operation

7.1 Charging the battery pack (Fig. 1)

The battery pack is protected from exhaustive di-

scharge. An integrated protective circuit automati-

cally switches off the equipment when the battery

pack is ﬂ at. In this case the bit chuck (1) will cease

to turn.

 Caution:

Do not press the ON/OFF switch (9) any more,

if the protective circuit has actuated. This may da-

mage the battery pack.

1. Check that your mains voltage is the same as

that marked on the rating plate of the battery

charger. Plug the battery charger (11) in the

plug socket and connect the charging cable

(12) to the charging connection (8). The char-

ging process starts as soon as the charging

cable is connected to the charging connec-

tion.

2. The charging control lamp (7) indicates that

the battery is being charged.

3. The charging control lamp (7) goes out when

charging is completed.

 Caution:

The handle may become a little warm during the

charging process. This is normal.

If the battery pack fails to charge, please check

•

whether there is voltage at the socket-outlet.

•

whether there is good contact at the charging

contacts of the battery charger (11).

If the battery still fails to charge, send

•

the battery charger (11)

•

and the screwdriver

to our customer services department.

Timely recharging of the battery pack will help to

prolong its lifespan. You must recharge the bat-

tery pack when you notice that the power of the

screwdriver drops.

7.2 Clockwise/Counter-clockwise chan-

geover switch (Fig. 2/Item 10)

The clockwise/counter-clockwise changeover

switch (10) above the ON/OFF switch (9) is

for setting the direction of rotation of the cord-

less screwdriver and for preventing the cordless

screwdriver from being switched on inadvertently.

You can select between clockwise and counter-

clockwise rotation.

 Important.

Change the direction of rotation only when the

equipment is at a standstill. If you fail to observe

this point, the gearing may become damaged.

When the clockwise/counter-clockwise changeo-

ver switch (10) is in the middle position, the ON/

OFF switch (9) is blocked.

Direction Switch position

Clockwise “R” pressed

Counter-clockwise “L” pressed

7.3 ON/OFF switch (Fig. 2/Item 9)

Press the ON/OFF switch (9) to switch the cord-

less screwdriver on. Release the ON/OFF switch

to switch off the tool.

7.4 LED lamp (Fig. 2/Item 2)

The LED lamp (2) can be used in poor lighting

conditions to illuminate the area where you want

to screw. To switch ON, press the switch (4) and

to switch OFF, press the switch (4) again.

Anl_4513422.indb 55Anl_4513422.indb 55 25.10.12 18:3325.10.12 18:33

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 86735 PASS 3.6 A1 Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info