Bedienungsanleitung Parkside IAN 89169 PBSG 95 A1 (Seite 33 von 36) (Deutsch, Englisch, Holländisch, Französisch)

745087

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

33 GB

UseGeneral safety advice

Use

Sharpening a drill

NOTE: Badly damaged drills should ﬁrst be coarsely

sharpened on a sharpening block.

Fully lower the sharpening stone. To do this turn

the rotary switch

in the DOWN direction

as far as it will go.

Insert the drill into the smallest suitable drill

guide

on the drill sharpener. The exact size

(Ø) of each drill guide

is shown by the ad-

jacent lettering (3 to 10).

Press the ON / OFF switch

into position “I”

to switch on the device.

Turn the rotary switch

in the UP direction

until you hear a grinding noise.

NOTE: The rotary switch

controls the posi-

tion of the sharpening stone in the sharpening

head housing and therefore the pressure of the

sharpening stone against the drill. The further

you turn the rotary switch

in the UP direction

the greater the pressure. Ensure that you do not

turn the sharpening stone too far up. Otherwise

the sharpening stone could strike the housing.

Turn the drill under slight pressure loosely and

quickly to and fro between the left and right

stops about 10 times (with small drills about 5

times).

Pull the drill out, turn it through 180° (horizon

tally)

and insert it again until it meets the sharpening

stone.

If necessary repeat whole process until both

cutting edges of the drill are sharp. Control the

grinding operation so that the angle between

the main and transverse cutting edges for a

standard drill is 130°. Both cutting edges (b)

must have the same angle to the drill axis (a)

and be the same length so that the drill runs

concentrically (see following ﬁgures).

(b)(b)

(a)

Press the ON / OFF switch

into position “0”

to switch oﬀ the device.

Replacing the

sharpening stone

RISK OF INJURY! Before you

carry out any work on the device, always pull the

mains plug out of the mains socket. Replace the

sharpening stone if it is worn out or damaged

(deteriorating, irregular sharpening performance,

broken stone). A Phillips screwdriver is required for

this step.

Screw the four screws

out of the sharpening

head cover

and remove the cover

, refer

to Fig. A.

Take out the sharpening stone

Clamp the sharpening stone

in a vice. Re-

lease the threaded connection

, which holds

the sharpening stone

on to the sharpening

stone holder

, using a 22 mm open spanner,

see Fig. B.

NOTE! LEFT-HAND THREAD - TO RELEASE

TURN IT CLOCKWISE!

Remove the metal washer

Mount the new sharpening stone, with its ﬂat-

tened edge facing downwards, on to the

sharpening holder

and reinsert the metal

washer

Clamp the sharpening stone

again in a vice

and tighten the threaded connection

using

a 22 mm open spanner.

NOTE! LEFT-HAND THREAD - TO TIGHTE

TURN IT ANTICLOCKWISE!

Ensure that the spring

is inserted into the

device in accordance with Fig. D and insert the

sharpening stone back into the device. Turn the

sharpening stone until it goes precisely back

into place, as shown in Fig. A, otherwise the

sharpening stone cover

cannot be ﬁtted.

Place the sharpening stone cover

back in

position and screw it in place with the four

screws

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 89169 PBSG 95 A1 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info