Bedienungsanleitung Parkside IAN 89567 PDFP 500 A1 (Seite 41 von 44) (Deutsch, Holländisch, Französisch, Italienisch)

745112

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

41 GB

Initial use / Maintenance and Cleaning

- When working with the device you should open

the vent

- When diluting the material, make sure that the

spraying material and the dilution are suitable

for one another. If an incorrect dilution is used,

lumps may form and clog the gun as a result.

- Screw the ﬂow cup

clockwise ﬁrmly on to

the gun.

- Fill the spraying material into the ﬂow cup

and screw the lid

on tight.

- Always hold the paint spray gun at the same

distance from the object. The ideal spraying

distance is approximately 15 cm.

- Determine the appropriate settings in each

case by experimenting.

- Do not turn the device on / oﬀ when it is over the

spraying surface, but start and end the spraying

process approximately 10 cm outside of the

spraying area.

Press the trigger

to start spraying and keep

it held down.

In order to stop spraying, release the trigger

again.

Adjusting the paint jet

The device has the settings round and broad jet.

Round jet Broad jet

Adjusting the round jet:

Use the round jet, for example, for small surfaces,

corners and edges.

Turn the regulator

in a clockwise direction .

Adjusting the broad jet:

Use the broad jet vertically and horizontally

over larger areas.

Turn the regulator

in an anticlockwise direc-

tion

. The nozzle head

can be continuously

adjusted vertically and horizontally by turning

to the desired position.

Regulating the

quantity of paint

Note: The front locking screw is used to limit the

adjustment range of the stroke stop screw

Increasing the quantity of paint:

Turn the stroke stop screw

in an anticlockwise

direction.

Reducing the quantity of paint:

Turn the stroke stop screw

in a clockwise

direction.

Regulating the quantity of air

Note: It is advisable to start with the maximum

amount of air. In order to do this, open the air volume

regulator

as described below under “Increas-

ing the air quantity” up to the maximum setting.

Increasing the air quantity:

Note: Increasing the amount of air is generally

advisable when the degree of atomization is too

coarse.

Turn the air quantity regulator

in an anti-

clockwise direction.

Reducing the air quantity:

Note: Reducing the amount of air is generally

advisable when the paint spray is too strong.

Turn the air quantity regulator

in a clock-

wise direction.

Maintenance and Cleaning

Note: Thorough cleaning after each use is very

important for safety and operation. Otherwise, for

example, the needle will become clogged and the

proper functioning of the appliance can no longer

be guaranteed.

Wear suitable protective gloves when carrying

out cleaning work.

Do not use any hydrocarbon-containing halogen

solvents, such as trichloromethyl, ethyl chloride,

etc., as they undergo chemical reactions with

Safety advice / Initial use

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 89567 PDFP 500 A1 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info