Bedienungsanleitung Parkside IAN 89568 PDT 40 C2 (Seite 31 von 36) (Deutsch, Englisch, Holländisch, Französisch)

745116

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

31 GB

Introduction / Safety of the fastener driving tool

In correspondence with conditions at the work loca-

tion, individual noise reduction measures may need

to be carried out, such as placing the workpiece on

a noise-suppressing surface, clamping or covering

to prevent workpiece vibration and adjusting to the

minimum pressure required by the work process. In

certain cases, wearing personal hearing protection

is require.

Wear hearing protection!

Vibration values in accordance with

ISO 8662-11:1999:

Vibration emission value a

h,W

= 15.0 m / s

Uncertainty K = 0.29 m / s

Mechanical impact (vibration)

The vibration value for the fastener driving device was

determined in accordance with ISO 8662-11:1999 —

Hand-held portable power tools – Measurement of

vibrations at the handle — Fastener driving tools

(see technical data). The value is referenced to the

device and does not represent the inﬂuence on the

hand-arm system when the device is used. Inﬂuence

on the hand-arm system when using the device de-

pends on e.g. gripping force, pressing force, work-

ing direction, air pressure set, the workpiece and its

position.

Safety of the fastener

driving tool

Please read

all the safety information and

instructions. Failure to comply with

the safety instructions and instructions can result in

severe injuries and / or damage to property.

PLEASE RETAIN ALL SAFETY INFORMATION

AND INSTRUCTIONS FOR FUTURE REFERENCE.

Each time before starting work, check

for flawless functioning of the safety

and triggering devices as well as the

firm fit of all bolts and nuts.

Do not conduct any improper manipu-

lation of the fastener driving tool.

Do not dismount or block any part of

the fastener driving tool, such a trig-

ger lock.

Do not conduct any „emergency re-

pairs“ with unsuitable materials.

The fastener driving tool must be reg-

ularly and properly maintained as

specified by the manufacturer.

Prevent anything that would weaken

or damage the device, e.g. by:

– stamping or engraving,

– alterations not permitted by the

manufacturer,

– guiding on templates made of hard

material, e.g. steel,

– permitting to fall onto or slide across

the floor,

– using as a hammer,

– every type of external force.

Work safety

Never point a fastener driving tool that

is ready to use directly at yourself,

other persons or animals.

During work, hold the fastener driving

tool so that head and body can not be

injured by possible kickback due to a

fault in the power supply or from hard

places in the workpiece.

Never trigger the fastener driving tool

into empty space. Following this instruction

will prevent danger due to uncontrolled ﬂying

fasteners and overloading the device.

Before transporting, disconnect the

fastener driving tool from the com-

pressed air network, particularly when

using ladders or are moving with an

unaccustomed body posture.

At the workplace, only carry the fas-

tener driving tool by its grip and never

with the trigger actuated.

Pay attention to workplace conditions.

Fasteners may strike completely through thin

workpieces or slide oﬀ corners or edges to

cause a danger to persons.

Introduction

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 89568 PDT 40 C2 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info