Bedienungsanleitung Parkside IAN 89570 PDEXS 150 A1 (Seite 48 von 51) (Französisch)

745094

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

48 GB

Information about warranty and service processing

Initial use /Working instructions / Cleaning

Initial use

Connecting the compressed

air source

Note: Only operate the compressed air orbital

sander with cleaned, condensate-free compressed

air. Never exceed the unit‘s maximum operating

pressure of 7.5 bar.

Note: The compressed air source must be ﬁtted

with a (ﬁlter) / pressure reducer to allow the air

pressure to be regulated.

Switching on and oﬀ

Note: Always switch on the compressed air orbit-

al sander before bringing it into contact with the

work piece.

Switching on the compressed air orbital

sander:

Press the operating lever

all the way down

(see Fig. C).

Adjust the speed with the speed control

Switching off the compressed air orbital

sander:

Release the control lever

Disconnect the unit from the compressed air

source after ﬁnishing the work.

Note: First disconnect the hose from the

compressed air source (compressor), only then

disconnect the supply hose from the unit. This

will ensure that the compressed air supply hose

does not wave around or recoil in an uncon-

trolled manner.

Working instructions

Wait until the device has come to a standstill

before you put it down.

Sanding surfaces

Switch on the compressed air orbital sander,

place the entire sanding surface on the surface

to be worked and move it across the work

piece with moderate pressure (see Fig. D).

Note: The sanding output and pattern greatly

dependent on the sanding disc selected and

the pressure applied. Only grinding discs that

are in perfect condition will provide good

grinding performance.

Be sure to apply pressure evenly to increase

the life of the sanding discs.

A sanding sheet previously used on metal must

not be used on other materials.

Replacing the backing plate

RISK OF INJURY! Always

disconnect the device from the compressed air

source before you replace the backing plate

Push the open-ended spanner

between the

backing plate

and collar

Release the backing plate

by turning the

plate anticlockwise and holding the open-ended

spanner

still against this movement.

Screw on a new backing plate

clockwise

until tight while holding the open-ended span-

ner

still against this movement.

Cleaning

RISK OF INJURY! Be

absolutely certain to disconnect the device

from the compressed air source before clean-

ing or maintaining it.

Clean the air sander after you have ﬁnished

using it.

Store the air sander in dry enclosed rooms only.

Use a dry cloth to clean the device. Under no

circumstances should you use petrol, solvent or

cleaners which attack plastic.

Keep the ventilation openings clear at all times.

Remove abrasive dust with a brush.

89570_par_Druckluft_Exzenterschleifer_content_LB2.indd 48 29.05.13 17:33

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 89570 PDEXS 150 A1 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 89570 PDEXS 150 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info