Bedienungsanleitung Parkside IAN 89959 PMGS 12 B2 (Seite 49 von 52) (Deutsch, Englisch, Holländisch, Französisch)

745110

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

49 GB

OperationGeneral safety advice for electrical power tools / Operation

mended in the operating instructions could lead

to you suﬀering an injury.

Inserting or replacing

a tool / collet

Press the spindle lock

and keep it pressed.

Rotate the clamping nut

until the lock

engages.

Loosen the clamping nut

with the combina-

tion key

If a tool is already inserted, remove it.

First insert the tool you wish to use though the

clamping nut

before you insert it into the

collet

suitable for the tool shaft.

Press the spindle lock

and keep it pressed.

Insert the collet

into the threaded insert and

tighten the clamping nut

on the thread using

the combination key

Using the Insertion tool with mandrel

NOTE: Use the screwdriver end of the combi-

nation key

to release or tighten the screw of

the mandrels

Insert the mandrel

into the electrical tool as

described.

With the aid of the combination wrench

unscrew the screw from the mandrel

Place the insertion tool you wish to have onto

the screw between the two washers.

With the aid of the combination wrench

tighten the screw on the mandrel

Switching on and oﬀ /

Setting the speed range

Switching on / Setting the speed range:

Connect the plug

to the power supply unit

by inserting it into the plug-in device

provided

for such purposes (see Fig. C).

Connect the device to the power supply by

inserting the mains plug into the socket.

Press down the ON / OFF switch

and then

move it in direction of the rotational speed con-

trol

. Then set the rotational speed control to

a position between “5” and “20”.

Switching off:

Set the rotational speed control

to position

“5”. Press down the ON / OFF switch

and

then move it in direction of the cable.

Advice on working with

materials / Tools / Speed ranges

Use the highest speed when working on steel

or iron with the milling bits

Use a short trial on a test piece to determine the

optimum rotational speed range for working on

zinc, zinc alloy, aluminium, copper and lead.

Use the low speed range for working on plastics

and low-melting point materials.

Use high speeds on wood.

Use the medium speed range for cleaning,

polishing and buﬃng.

The following information shall be considered as

recommendatory only. Learn by practical experience

which tools and settings are the best for the materi-

als you work with.

Setting the appropriate speed:

Numeral on the

rotational speed

control

Material to be

worked on

Plastics and low melting

point materials

Stone, Ceramics

Softwood, metal

Hardwood

Steel

Examples of appropriate tool selection

Function:

Function Accessory Application

Drilling

HSS drill

Drilling wood

Milling Milling bits

Various tasks, e.g.

hollowing out,

gouging, shaping,

grooving or slotting

89959_par_Modellbau- und Gravierset_content_LB2.indd 49 29.05.13 15:52

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 89959 PMGS 12 B2 Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info