Bedienungsanleitung Parkside IAN 90983 PWS 125 A1 (Seite 36 von 49) (Deutsch, Englisch, Holländisch)

745196

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

36 GB

Introduction / General safety advice for electrical power toolsIntroduction

Angle grinder PWS 125 A1

Grinding, roughing, cutting

Introduction

We congratulate you on the purchase of your new

device. You have chosen a high quality product. The

instructions for use are part of the product. They

contain important information concerning safety,

use and disposal. Before using the product, please

familiarise yourself with all of the safety information

and instructions for use. Only use the unit as de

scribed

and for the speciﬁed applications. If you pass the

product on to anyone else, please ensure that you

also pass on all the documentation with it.

Proper use

This tool is suitable for cutting, roughening and

brushing metal materials without the use of water.

Any other use or modiﬁcation to the device shall be

considered as improper use and could give rise to

considerable dangers. We will not accept liability

for loss or damage arising from improper use. The

device is not intended for commercial use.

Note: Slots cut in load-bearing walls must comply

with standard DIN 1053 Part 1 or the regulations

applicable in your country.

These instructions and advice must be observed.

Before you start a task, seek the advice of a com-

petent structural engineer, architect, or the relevant

site management staﬀ.

Features and equipment

Safety lock-out

ON / OFF switch

Carbon brushes cover

Auxiliary handle

Adjustable disc guard

Clamping nut

Mounting spindle

Mounting ﬂange

Spindle lock button

Speed pre-selector wheel

Spanner (Fig. B)

Included items

1 Angle grinder PWS 125 A1

1 Metal-cutting disc

1 Auxiliary handle

1 Disc guard cover

1 Spanner

1 Operating instructions

Technical information

Rated input: 1200 W

Rated voltage: 230–240 V∼, 50 Hz

Rated no-load speed: n 12000 rpm

Variable rotation speed: 3000 to 12000 rpm

Spindle thread: M14

Protection class: II /

Noise and vibration data:

Measured values for noise are determined in accor-

dance with EN 60745. The A-weighted noise level

of the electrical power tool are typically:

Sound pressure level: 91 dB(A)

Sound power level: 102 dB(A)

Uncertainty K: 3 dB

Wear hearing protection!

Vibration total values determined

according to EN 60745:

Surface grinding:

Vibration emission value a

h, AG

= 13.431 m/s

Uncertainty K = 1.5 m/s

The vibration level speciﬁed in

these instructions was measured in accordance with

an EN 60745 standardised measurement process

and can be used to compare equipment. The vibra-

tion emission value speciﬁed can also serve as a

preliminary assessment of the exposure.

The vibration level will change according to the ap-

plication of the electrical tool an in some cases may

exceed the value speciﬁed in these instructions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 90983 PWS 125 A1 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 90983 PWS 125 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info