Bedienungsanleitung Parkside IAN 90983 PWS 125 A1 (Seite 46 von 51) (Französisch)

745196

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

46 GB

General safety advice for electrical power tools / Use

For the best grinding performance move the

device evenly to and fro over the workpiece

maintaining an angle of 15° to 30° (between

grinding disc and workpiece).

When working on inclined surfaces do

not press the device hard down on to

the workpiece. If the speed slows greatly,

use less pressure. This will allow you to work m

ore

eﬀectively and safely. If the device suddenly

stops due to it becoming retarded or trapped,

pull the mains plug from the socket immediately.

Cutting: Advance the device at an

appropriate rate. Do not incline the

cutting disc.

Roughing, grinding and cutting discs

get hot during use – allow them to

cool fully before touching them.

Never use the device for a purpose

for which it was not intended.

Before you insert the mains plug into

the socket, always check that the de-

vice is switched off.

If a dangerous situation arises, pull

the mains plug immediately out of the

mains socket. Ensure that the device and

the mains plug are easily accessible and can

be reached quickly in an emergency.

When taking a break from your

work, before carrying out any tasks

on the device itself and when you are

not using the device, always pull the

mains plug out of the mains socket.

Always keep the device clean, dry and free of

oil or grease.

Remain alert at all times! Always watch

what you are doing and proceed with

caution. Do not use the device if you cannot

concentrate or you are feeling unwell.

Use

Switching on and oﬀ

Check the attached consumable or tool before use.

It must be attached properly, not damaged, damp

or cracked and must rotate freely. Test the operation

of the device for 30 seconds. If a disc is not round

or vibrates, do not use it. Look out for unusual noises

or generation of sparks. Check that all the fastenings

are correctly attached.

Switching on:

Press the safety lock-out

Press the ON / OFF switch

Switching off:

Release the ON / OFF switch

again.

Setting the speed

Select the desired speed before use to suit your

purpose. Turn the speed preselector wheel

to the desired setting. The required rotational

speed depends on the material being worked

and the working conditions and can be deter-

mined by means of a practical test.

The table below shows some recommended

settings (for guidance only and given without

liability) for a number of common applications.

The accessories mentioned may not all be sup-

plied as standard with the product.

Preselected rotation speed:

Material

Application

Tool Setting

Plastic,

varnish

Polishing Lambswool

bonnet

Fine ﬁnish

Felt polishing

disc

Metal Fine ﬁnish Buﬃng disc 1

Paint

removal

Sanding sheet 2–3

Wood,

metal

Brushing,

derusting

Cup brush,

sanding sheet

Metal Grinding /

abrading

Grinding disc 4–6

Metal Roughing /

grinding

Roughing /

grinding disk

Metal Cutting Cutting disc 6

Use / Use of accessories

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 90983 PWS 125 A1 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 90983 PWS 125 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info