Bedienungsanleitung Parkside IAN 93497 PSFS 250 A1 (Seite 9 von 58) (Deutsch, Englisch, Holländisch, Französisch, Schwedisch)

745190

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

9 GB/IE

Additional safety … / Additional safety information for routers / Operation

Additional safety information

for grinders and polishers

POISONOUS DUSTS! The working of mate-

rials that can produce harmful / toxic dusts

presents a health risk for the operator and for

people located in the close vicinity.

Avoid sanding of paints containing lead or other

material detrimental to your health.

Do not work on materials containing asbestos.

Asbestos is considered carcinogenic.

Wear safety glasses and a dust protection mask!

Additional safety information

for routers

Hold the device by the insulated handle

surfaces as there is a danger of the

cutter striking the device’s mains

lead. Contact with a live wire could cause

metal parts of the device to become live and

lead to electric shock.

Only use cutting bits with the correct size shaft

diameter suitable for the speed of the electric tool.

Fix and secure the work piece to a

stable surface using clamps or other

means. If you only hold the work piece with

your hand or against your body, it will remain

unstable which could lead to a loss of control.

Operation

Never use the device for any purpose other than

the intended purpose and only use it with the origi-

nal parts and accessories. The use of parts or ac-

cessories other than those recommended in the

operating instructions could lead to you suﬀering

an injury. Use only an extension cable that has

been completely unrolled and is undamaged with

a capacity of at least 5 A.

WARNING: Do not use this tool for the creation

of notches in the vicinity of installations or openings

with live electric cables or in walls behind which

live electric cables could potentially be laid. The bit

could conduct electricity into the tool and this could

involve the risk of electric shock to the operator.

Trigger the circuit breaker or remove the fuse in

order to disconnect the relevant electric circuit.

Attention: Always hold the tool on the plastic

housing and always wear safety goggles when

working with the tool.

Switching ON / OFF (see Fig. A)

Switching on:

Press the ON / OFF switch

Switching off:

Release the ON / OFF switch

Setting the speed (see Fig. B)

Turn the speed controller

in a clockwise

direction to increase the speed.

Turn the speed controller

in an anticlockwise

direction to reduce the speed.

Changing tools (see Fig. C)

Note: Only use combination cutter accessory

parts with a shaft diameter of ø 4.8 mm.

Hold the spindle lock button

pressed down.

Loosen the clamping nut

with the wrench

by turning in an anticlockwise direction.

Change the tool.

Block the spindle lock, tighten the clamping

nut

using the open-ended spanner

Bits:

The bits included are intended for the following

applications (see Fig. D).

Multi-purpose cutter (HSS)

Application: wood, particle board, plastic, alumini-

um and iron sheets

Slot cutter (HSS)

Application: wood, particle board, plastic

Sanding belts

Application: sanding wood

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 93497 PSFS 250 A1 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info