Bedienungsanleitung Parkside IAN 93523 PWS 125 A1 (Seite 13 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Schwedisch)

745195

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

13 GB/IE

General safety advice for electrical power toolsGeneral safety advice for electrical power tools

For safety reasons this device must

always be used with the auxiliary

handle

in place.

The adjustable disc guard cover

must

always be in place when working with

roughing, grinding or cutting discs.

Otherwise there could be danger of injury.

Use the vacuum dust extraction facility

if your work generates high amounts

of dust. Use suction devices particular-

ly approved for the purpose.

Use permitted consumables and tools

only. Check that the speed given on the

discs is greater or equal to the rated

speed of the device.

Take note of the direction of rotation

and always hold the device in such a

way that the sparks and grinding de-

bris are thrown away from your body.

Otherwise there could be danger of injury.

Make sure that the dimensions of the

disc are suitable for the device and

that the disc is of a type that fits prop-

erly on to the mounting flange

Advice on use

Note! Discs must be used only for their recom-

mended purposes, otherwise they could disintegrate,

become damaged or cause accidents.

Roughing (see Fig. G):

Never use cutting discs for

roughing or grinding!

Move the angle grinder using even

pressure to and fro over the workpiece.

Hold the roughing or grinding disc at

a flat angle to the workpiece when

working on a soft material. Use a

slightly steeper angle for harder ma-

terials.

Disc-cutting (see Figs. E, F):

Never use roughing or

grinding discs for cutting!

Only use certified fibre-reinforced cut-

ting or grinding discs approved for use at

circumferential speeds of not less than 80 m / s.

CAUTION! The disc continues to rotate after

the device has been switched oﬀ. Do not at-

tempt to slow it down by pressing on the side

of the disc.

Securely support the workpiece. Use

clamps or a vice to grip the workpiece ﬁrmly.

This is much safer than holding it in your hand.

Switch the device off and allow it to

come to a complete standstill before

you put it down.

Unlock the ON / OFF switch immedi-

ately if a power failure occurs or the

plug is pulled out of the mains socket.

Place the switch in the OFF position.

This prevents the device from being inadvertent-

ly started up again.

Use the device for dry cutting or dry

grinding only.

The auxiliary handle

must be in

place

whenever the device is being used.

Do not work on materials containing

asbestos. Asbestos is a known carcinogen.

A tip! Using the device safely.

DANGER! Always guide

the device through the

workpiece against the di-

rection of rotation of the

disc. If you work in the other direction there is

the risk of kickback. The device may be forced

out of the cut.

Always switch on the device before

placing it against the workpiece. After

cutting or grinding, always lift the device from

the workpiece before switching it oﬀ.

When working always hold the device

securely with both hands (see Fig. G).

Always keep proper footing and balance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 93523 PWS 125 A1 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info