Bedienungsanleitung Parkside IAN 93548 PMNF 1350 A1 (Seite 30 von 34) (Deutsch, Englisch, Holländisch)

745201

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

30 GB

General power tool safety warnings / Start-up / OperationGeneral power tool safety warnings

Further safety instructions for

abrasive cutting-oﬀ operations

Kickback and related warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel. Pinching or snagging causes rapid

talling of the rotating wheel which in turn causes th

uncontrolled power tool to be forced in the direction

opposite of the wheel’s rotation at the point of the

binding.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into the

surface of the material causing the wheel to climb

out or kick out. The wheel may either jump toward

or away from the operator, depending on direction

of the wheel’s movement at the point of pinching.

Abrasive wheels may also break under these con-

ditions.

Kickback is the result of power tool misuse and / or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below.

a) Maintain a firm grip on the power tool

and position your body and arm to

allow you to resist kickback forces. Al-

ways use auxiliary handle, if provided,

for maximum control over kickback or

torque reaction during start-up. The op-

erator can control torque reactions or kickback

forces, if proper precautions are taken.

b) Never place your hand near the rotat-

ing accessory. Accessory may kickback over

your hand.

c) Do not position your body in line with

the rotating wheel. Kickback will propel

the tool in direction opposite to the wheel’s

movement at the point of snagging.

d) Use special care when working cor-

ners, sharp edges etc. Avoid bouncing

and snagging the accessory. Corners,

sharp edges or bouncing have a tendency to

snag the rotating accessory and cause loss of

control or kickback.

e) Do not attach a saw chain, woodcarv-

ing blade, segmented diamond wheel

with a peripheral gap greater than

10 mm or toothed saw blade. Such blades

create frequent kickback and loss of control.

f) Do not “jam” the wheel or apply ex-

cessive pressure. Do not attempt to

make an excessive depth of cut. Over-

stressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel

in the cut and the possibility of kickback or

wheel breakage.

g) When wheel is binding or when inter-

rupting a cut for any reason, switch

off the power tool and hold the power

tool motionless until the wheel comes

to a complete stop. Never attempt to

remove the wheel from the cut while

the wheel is in motion otherwise kick-

back may occur. Investigate and take cor-

rective action to eliminate the cause of wheel

binding.

h) Do not restart the cutting operation in

the workpiece. Let the wheel reach full

speed and carefully re-enter the cut.

The wheel may bind, walk up or kickback if

the power tool is restarted in the workpiece.

i) Support panels or any oversized work-

piece to minimize the risk of wheel

pinching and kickback. Large workpieces

tend to sag under their own weight. Supports

must be placed under the workpiece near the

line of cut and near the edge of the workpiece

on both sides of the wheel.

j) Use extra caution when making a

“pocket cut” into existing walls or

other blind areas. The protruding wheel

may cut gas or water pipes, electrical wiring

or objects that can cause kickback.

Supplementary Instructions

Approved cutting wheel designs: diamond

set, disc diameter 125 mm, disc thickness max.

2.2 mm

Always wear a dust mask!

Always wear ear protection!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 93548 PMNF 1350 A1 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 93548 PMNF 1350 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info