Bedienungsanleitung Parkside IAN 95929 PWS 230 A1 (Seite 43 von 46) (Französisch)

745197

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

43 GB

hot during use. Do not touch them until after

they have cooled down.

NOTE: Always ensure the discs are free of dirt

before use.

Use only abrasive consumables or tools with

an allowable speed at least as high as the

no-load speed of the device.

DANGER OF INJURY! Press the spindle lock

button

only after the mounting spindle

has reached a standstill.

Press the spindle lock button

to block the drive.

Release the clamping nut

using the spanner

(see Fig. C).

Place the roughing / grinding or cutting disc on

to the mounting ﬂange

with its labelled side

facing towards the device.

Then replace the clamping nut

, with its

raised side facing upwards, on to the mounting

spindle

Press the spindle lock button

to block the drive.

Tighten the clamping nut

again with the

spanner

NOTE: Replace a new disc immediately if it

runs unevenly or vibrates after being exchanged.

After replacing a disc let the device run under

no-load conditions for 30 seconds as a safety

check. Look out for unusual noises or generation

of sparks. Check that all the fastened-on parts

are correctly attached.

Pay attention to see that the arrow showing the

direction of rotation on the roughing / grinding

or cutting discs (including diamond cutting discs)

corresponds with the direction of rotation of the

device (see arrow on the head of the device).

Operation

Switching on and oﬀ

Note: Always switch on the angle grinder before

bringing it into contact with the workpiece material.

Switching on the device:

Press the safety lock-out

(see Fig. G).

Then press the ON / OFF switch

Switching oﬀ the device:

Release the ON / OFF switch

Rotating the hand grip:

DANGER OF INJURY!

Pull the mains plug out of the mains

socket before you carry out any task

on the device.

The hand grip

can be rotated by 90° to

the right or left (see Fig. A).

This allows the ON / OFF switch

to be

brought into the most comfortable position for

any working conditions.

Press the unlocking button

and rotate the

hand grip

to the right or left.

Make sure the hand grip

engages.

Maintenance and cleaning

DANGER OF INJURY!

Pull the mains plug out of the mains

socket before you carry out any task

on the device.

Do not use sharp objects for cleaning

the device. Do not allow any liquids

to enter the device. Otherwise the device

could be damaged.

Have the carbon brushes replaced only at the

service centre or an accredited electrical

equipment repair centre. The device requires

no other maintenance.

Clean the device frequently; for best results do

this immediately after you have ﬁnished using it.

Use a dry cloth to clean the housing – under

no circumstances use petrol, solvents or cleaning

agents that attack plastic.

A vacuum cleaner is required to thoroughly

clean the device.

Ventilation openings must always be kept free.

Remove any adhering dust with a narrow paint

brush.

Preparing for use / Operation / Maintenance and cleaningGeneral power tool safety warnings / Preparing for use

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 95929 PWS 230 A1 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 95929 PWS 230 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info