Bedienungsanleitung Parkside KH 3041 (Seite 25 von 37) (Deutsch, Englisch, Holländisch, Italienisch, Portugiesisch, Spanisch)

464929

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

25 GB/MT

7 bar. A pressure reducer must be ﬁtted to the com-

pressor to regulate the working air pressure.

j Connect the device to a suitable source of

compressed air.

1. To do this press, the quick-release coupling of

the compressed air hose (not supplied) on to

the threaded plug-in nipple ¼“ ext. dia.

the compressed air tacker. It locks itself in

place automatically.

2. Connect the other end of the compressed air

hose to the (ﬁlter) / pressure reducer at the

compressor.

Loading the magazine

NOTE: Never place nails into the intermediate

opening; this opening is intended for staples. Oth-

erwise this could lead to a blockage in the driver

and prevent the proper exit of the driven fastener.

1. Press the magazine lever

and pull back the

magazine

NOTE: Note that only staples with a length

of 16 - 32 mm and nails with a length of

15 - 32 mm may be placed in the magazine.

2. Place some compliant driven fasteners (nails,

see Fig.

or staples, see Fig.

) in the

magazine

3. Push the magazine

forward until it engages.

Operation

j Load the magazine

of the compressed air

tacker, as described in the section about

“Loading the magazine”.

j Using the pressure reducer, set the correct

working air pressure.

j Ensure that the maximum working air pressure

at the device of 7 bar is not exceeded. An in-

creased working air pressure does not improve

performance but only increases the consump-

tion of compressed air and accelerates wear.

j Switch compressor on.

j Allow the compressor to run until the maximum

reservoir pressure has been reached and then

switch oﬀ the device.

j Place the compressed air tacker on to the

workpiece and press the trigger

NOTE: The compressed air tacker

is ﬁtted with a trigger lock

. The

driven fastener only exits the device

if the opening of the compressed air tacker is

pressed against the workpiece and the trigger

is pressed. This safety feature ensures that

driven fasteners such as staples and nails can-

not exit the device in an uncontrolled manner.

j Check whether the driven fastener is driven into

the workpiece in accordance with your require-

ments.

- If the driven fastener projects above the work-

piece surface, increase the compressed air

pressure in 0.5 bar steps until a satisfactory

result is achieved.

- If the driven fastener lies too far below the

workpiece surface, reduce the working

pressure in 0.5 bar steps until a satisfactory

result is achieved.

In any event, you should make every eﬀort to work

using the lowest adequate compressed air pressure.

This brings you three important advantages:

1) You save energy,

2) You reduce the noise level,

3) You reduce the wear on the fastener driving tool.

j Avoid triggering the fastener driving tool if the

magazine is empty.

Bringing into use / Operation

32999_Druckluft-Tacker_Content_LB5 (ohne PT).indd 25 06.07.09 09:53

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside KH 3041 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info