Bedienungsanleitung Parkside KH 3113 (Seite 9 von 11) (Englisch)

464975

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

7 UK

or the relevant service centre.

· Do not operate the device if it is damp and do

not use it in a damp environment.

· If you use the device outdoors, always connect

it through a residual current device with a

maximum trip current of 30 mA.

If using an extension lead, always use one that

is approved for outdoor use.

· Always work with the mains lead leading away

from the rear of the device.

To avoid danger of injury and

hazards to health:

Wear protective glasses. Pieces of

material may split off the workpiece

and become projectiles. This could cause injury.

· Do not work on moistened materials or damp

surfaces.

· Do not soak the materials or the surface you

are about to work on with liquids containing

solvents. The heat generated during scraping

can give rise to poisonous vapours or gases

that are hazardous to health.

· Secure the workpiece by holding it in a clamp

or vice, otherwise the workpiece cannot be

securely held in place and could cause injury.

· Do not work on materials containing asbestos.

· When working, always hold the device se-

curely with both hands (see Fig. B).

Never support yourself by placing your hands

near or in front of the device or the workpiece

surface. You could be injured if anything slips.

· Danger! The sharp edges of the tools could

cause injury.

Wear

protective gloves.

· Caution! Keep children away from the mains

lead and do not allow them to use the device.

Children often underestimate the dangers as-

sociated with electrical equipment.

Using the device safely:

· If danger arises, pull the mains plug immedi-

ately out of the mains socket.

· Never use the device for a purpose for which it

was not intended.

· Handle the device carefully and treat it with

respect. Always keep the device clean, dry and

free of oil or grease.

· Remain alert at all times! Always watch what

you are doing and proceed with caution. Do

not use the device if you cannot concentrate or

you are feeling unwell.

í Before use

í Quick-change tool holder

½ Danger! The sharp edges of the tools could

cause injury.

½ The choice of tool depends on the intended

task. The supplied accessories are suitable for

the most common tasks (see ﬁ gures C, D, E

and F). Carry out a short test to determine the

best tool for the task.

1. Press the tool lock

backwards into the

“Unlock” position.

2. Push the tool attachment into the tool holder

until it reaches the stop.

3. Lock the tool attachment in place and press

the tool lock

forwards into the “Lock” posi-

tion.

½ Make sure you ﬁ t the tool the right way round.

The inside of the curve on the shank/working

edge of the tool attachment

must point

downwards.

í First use

The mains voltage at the mains socket must match

that shown on the rating plate on the device.

Devices marked with 230 V can also be operated

at 220 V.

Attention! When using the device, never allow the

ventilation slots to be covered.

Safety/Before Use/First use

Manual_UK_Inhalt.indd 7Manual_UK_Inhalt.indd 7 30.06.2005 10:26:59 Uhr30.06.2005 10:26:59 Uhr

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside KH 3113 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside KH 3113

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info