Bedienungsanleitung Parkside PABS 12 B2 - IAN 270217 (Seite 12 von 75) (Deutsch, Englisch, Holländisch, Dänisch, Schwedisch, Finnisch)

722887

Zoom out

Zoom in

Vorherige Seite

1/75

Nächste Seite

12 GB/IE

Tips and Tricks

When screwing into wood, metal and

other materials:

Screw bits are designated with their dimensions

and their shape. If you are unsure, always try

the particular screw bit out to see whether it sits

in the screw head without any free play.

Before you use the appliance, check to see that

the screw or drill bit is properly ﬁtted, i.e. located

centrally in the chuck.

Torque:

Smaller screws and bits in particular can be

easily damaged if you adjust the appliance with

too high a torque and/or rotation speed.

Hard screw bed:

Particularly high torques can occur, for example

with metal screws tightened by socket tool bits.

Select a lower rotation speed.

Soft screw bed:

You should also select a low speed in order not

to damage the wood workpiece surface through

contact with the metal screw head. Use a coun-

tersinker.

When drilling into wood, metal and other

materials:

With small diameter drill bits use a high drill

speed. For large diameter drill bits, use a low

drill speed.

For hard materials, select a low drill speed.

For soft materials, select a high drill speed.

Secure or ﬁx down the workpiece (if possible)

in a clamp or vice.

Mark the intended position of the hole with a

centre punch or a nail and select a low drill speed

for drilling.

Take the rotating drill bit out of the hole frequently

so that swarf or drill dust can be re-moved and

the hole and tool is ventilated.

Drilling in metal:

Use a metal drill bit (HSS). For the best results,

you should cool the bit with oil. Metal drill bits

can also be used to drill into plastic.

Drilling in wood:

Normally you should use a wood drill with a

centring point. You can screw small screws into

soft wood without the need for pre-drilling.

Cleaning and Maintenance

Pull the mains plug out of the mains socket and re-

move the rechargeable battery pack

every time

before you clean or maintain the device.

The Cordless Drill / Screwdriver is maintenance-free.

Always keep the device clean, dry and free of

oil or grease.

Clean the device immediately after you have

ﬁnished using it.

Do not allow any liquids to enter the device.

Use a cloth to clean the housing.

Never use petrol, solvents or cleaning agents

that might attack plastic.

When storing a lithium-ion battery for extended

periods, regularly check the charge. The optimal

charge is between 50 % and 80 %. The optimal

storage climate is cooling and dry.

Warranty

The warranty for this appliance is for 3

years from the date of purchase. The ap-

pliance has been manufactured with care

and meticulously examined before deliv-

ery. Please retain your receipt as proof

of purchase. In the event of a warranty

claim, please make contact by telephone

with our Service Department. Only in this

way can a post-free despatch for your

goods be assured.

The warranty covers only claims for material and

maufacturing defects, but not for transport damage,

for wearing parts or for damage to fragile compo-

nents, e.g. buttons or batteries. This product is for pri-

vate use only and is not intended for commercial use.

Preparing the tool for use / Cleaning and Maintenance / Warranty Warranty / Disposal

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PABS 12 B2 - IAN 270217 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info