764032
31
Zoom out
Zoom in
Vorherige Seite
1/132
Nächste Seite
30 GB/IE
7) Follow all charging instruction and
do not charge the battery pack or
tool outside the temperature range
specified in the instruction. Charging
improperly or at temperatures outside the
specified range may damage the battery
and increase the risk of the fire.
Service
1) Have your power tool serviced by
a qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool is
maintained.
2) Never service damaged battery
packs. Service of battery packs should be
only be performed by the manufactured or
authorized service providers.
Drill safety warnings
1. Safety instructions for all operations
1) Hold the power tool by insulated
gripping surfaces, when performing
an operation where the accessory
tool or fasteners may contact
hidden wiring. Accessory tools or
fasteners contacting a “live” wire may make
exposed metal parts of the power tool “live”
and could give the operator an electric
shock.
2. Safety instructions when using long
drill bits
1) Never operate at higher speed
than the maximum speed rating of
the drill bit. At higher speeds, the drill bit
is likely to bend if allowed to rotate freely
without contacting the workpiece, resulting in
personal injury.
2) Always start drilling at low speed
and with the drill bit tip in contact
with the workpiece. At higher speeds,
the drill bit is likely to bend if allowed
to rotate freely without contacting the
workpiece, resulting in personal injury.
3) Apply pressure only in direct line
with the drill bit and do not apply
excessive pressure. Drill bits can bend
causing breakage or loss of control, resulting
in personal injury.
Vibration and noise reduction
To reduce the impact of noise and vibration
emission, limit the time of operation, use low-
vibration and low-noise operating modes as well
as wear personal protective equipment.
Take the following points into account to minimise
the vibration and noise exposure risks:
¾Only use the product as intended by its
design and these instructions.
¾Ensure that the product is in good condition
and well maintained.
¾Use correct accessory tools for the product
and ensure they are in good condition.
¾Keep tight grip on the handles / grip surface.
31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PABSP 20-Li B2 - IAN 322691 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info