Bedienungsanleitung Parkside PABSW 10.8 A1 - IAN 86583 (Seite 73 von 82) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

722879

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

- 73 -

For the protection of the operator it is essential to

specify safety measures which are based on an

estimate of the exposure during the actual condi-

tions of use (all stages of the operating cycle must

be considered, e.g. times in which the electric

tools are switched off and times in which the tool

is switched on but operates without load).

Residual risks

Even if you use this electric power tool

in accordance with instructions, certain

residual risks cannot be rules out. The fol-

lowing hazards may arise in connection

with the equipment’s construction and

layout:

1. Lung damage if no suitable protective dust

mask is used.

2. Damage to hearing if no suitable ear protec-

tion is used.

3. Health damage caused by hand-arm vib-

rations if the equipment is used over a pro-

longed period or is not properly guided and

maintained.

6. Before starting the

equipment

Be sure to read the following information before

you use your cordless screwdriver for the ﬁ rst time:

1. Charge the battery pack with the charger

supplied. An empty battery pack requires a

charging period of approximately one hour.

2. Only ever use sharp drill bits and screwdriver

bits which are suitable for the purpose and in

faultless condition.

3. Always check for concealed electric cables

and gas and water pipes when drilling and

screwing in walls.

7. Operation

7.1 Charging the LI battery pack (Fig. 2-3)

The battery is protected from exhaustive dischar-

ge. An integrated protective circuit automatically

switches off the equipment when the battery is ﬂ at.

In this case the bit chuck will cease to turn.

Warning! Do not press the ON/OFF switch any

more if the protective circuit has actuated. This

may damage the battery.

1. Remove the battery pack (5) from the handle,

pressing the pushlock buttons (6) on the left

and right sides to do so.

2. Check that your mains voltage is the same as

that marked on the rating plate of the battery

charger. Insert the power plug of the charger

(11) into the mains socket outlet. The green

LED will then begin to ﬂ ash.

3. Insert the battery pack (5) into the battery

charger (11).

4. In section 10 „Charger indicator“ you will

ﬁ nd a table with an explanation of the LED

indicator on the charger.

If the battery pack fails to become charged, ple-

ase check

•

whether there is voltage at the socket-outlet

•

whether there is proper contact with the char-

ging contacts in the battery charger (11).

If the battery still fails to become charged, please

return

•

the charger and charging adapter

•

the battery pack

to our Customer Service Department.

To ensure that the LI battery pack provides long

service you should take care to recharge it

promptly. You must recharge the battery pack

when you notice that the power of the cordless

screwdriver drops.

Anl_4513640.indb 73Anl_4513640.indb 73 27.11.12 13:4927.11.12 13:49

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PABSW 10.8 A1 - IAN 86583 Seite 73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info