Bedienungsanleitung Parkside PAMFW 10.8 A1 - IAN 96269 (Seite 30 von 34) (Französisch)

576740

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

30 GB

services providers. Contact with electricity

cables can lead to ﬁre or electric shock.

Damaging a gas pipe can lead to an explo-

sion. Penetration of a water pipe can lead to

property damage or to electric shock.

If you use the device outdoors, always

connect it through a residual current

device (RCD) with a maximum trip

current of 30 mA. If using an extension lead,

always use one that is approved for outdoor

use.

Any harmful / noxious dusts

generated from sanding represent a risk to the

health of the person operating the device and

to anyone near the work area.

Wear safety glasses and a dust pro-

tection mask!

Ensure that there is adequate ventila-

tion when working on plastic, paint,

varnish etc.

Do not soak the materials or the sur-

face you are about to work on with

liquids containing solvents.

Safety notices for chargers

Children or persons who lack the knowledge or

experience to use the device or whose physical,

sensory or intellectual capacities are limited

must never be allowed to use the device without

supervision or instruction by a person responsi-

ble for their safety. Children must never be

allowed to play with the device.

Advice on use

Principle of operation:

The oscillating motor allows the application tool to

oscillate back and forth 5000 to 19000 times per

minute. This allows for accurate working in the tight-

est of spaces.

Sawing / cutting:

Use only undamaged, defect-free saw blades.

Distorted, blunt or otherwise damaged saw

blades could break.

When sawing lightweight building materials,

observe the statutory requirements and the

manufacturer’s recommendations.

Use the device in plunge sawing mode on soft

materials such as wood, gypsum plaster board

etc. only!

Sanding:

Ensure that you use even contact pressure. This

will increase sanding sheet life.

Before use

Removing / charging / inserting

the battery pack

NOTE: The battery pack is delivered partly charged.

Charge the rechargeable battery in the charging

station for at least 1 hour before ﬁrst use. This will

ensure the battery delivers full power. Li-Ion batteries

can be charged at any time without reducing the life.

Interrupting the charging process does not damage

the rechargeable battery.

1. To remove the battery pack

press the release

buttons

and slide the battery pack

out of

the unit.

2. Insert the rechargeable battery pack

into the

rapid charger

3. Insert the mains plug into the mains socket. The

status LED

will light up red.

4. The green charging status LED

indicates the

charging process has been completed and the

battery pack

is ready for use.

5. Slide the battery pack

into the unit.

Start-up

Checking the battery charge

When the device is on, the battery status indicator

indicates the status or the remaining power as follows:

RED / ORANGE / GREEN = maximum

charge / power

RED / ORANGE = medium charge / power

RED = low charge – recharge battery

Start-upGeneral safety advice for electrical power tools / Before use / Start-up

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PAMFW 10.8 A1 - IAN 96269 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PAMFW 10.8 A1 - IAN 96269

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info