779294
11
Zoom out
Zoom in
Vorherige Seite
1/75
Nächste Seite
PAMFW 20-Li A1 GBIENI 7
Working procedures
Working principle
The oscillating drive causes the application tool to
move back and forth at a speed of 5000–19000
times per minute. This allows for precision work
even in confined spaces.
Sawing/cutting
Use only undamaged saw blades that are in
perfect working order. Bent, blunt or otherwise
damaged saw blades may break.
When sawing lightweight construction mate-
rials, follow the statutory regulations and all
recommendations from the material manufac-
turers.
Only soft materials such as wood, plasterboard
or similar should be processed using the plunge
saw process.
Sanding
To prolong the service life of the sanding
sheets , ensure that you apply even pressure.
Before use
Attaching/disconnecting the battery
pack to/from the appliance
Inserting the battery pack
Push the battery pack into the handle until it
clicks into place.
Removing the battery pack
Press the release button and remove the
battery pack .
Checking the battery charge level
Press the battery charge level button to
check the status of the battery (see also main
diagram).
The status/remaining charge will be shown on
the battery display LED as follows:
RED/ORANGE/GREEN = maximum charge
RED/ORANGE = medium charge
RED = low charge – charge the battery
Charging the battery pack
(seefig.A)
CAUTION!
Always unplug the appliance before you
remove the battery pack from or connect the
battery pack to the charger.
NOTE
Never charge the battery pack if the ambient
temperature is below 10°C or above 40°C.
If a lithium-ion battery is to be stored for an
extended period, the charge level should be
checked regularly. The optimum charge level
is between 50% and 80%. The storage climate
should be cool and dry and the ambient
temperature should be between 0°C and
50°C.
Connect the battery pack to the high-speed
battery charger (see Fig. A).
Insert the power plug into the socket.
The control LED lights up red.
The green LED indicates that the charging
process is complete and the battery pack is
ready.
CAUTION!
If the red control LED flashes, this means
that the battery pack has overheated and
cannot be charged.
If the red and green control LEDs both
flash, this means that the battery pack is
defective.
WARNING! RISK OF INJURY!
Always remove the battery before working on
the power tool.
Push the battery pack into the appliance.
Switch off the charger for at least 15 minutes
between successive charging sessions. Also
disconnect the power plug from the mains
power socket.
IB_339108_PAMFW20-LiA1_LB6.indb 7 09.03.20 11:46
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PAMFW 20-Li A1 - IAN 339108 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info