Bedienungsanleitung Parkside PBKS 53 A1 - IAN 315116 (Seite 30 von 120) (Deutsch, Englisch, Holländisch, Französisch)

782041

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

26 GB/IE

Working procedures

Get to know the chainsaw before you start to use it.

Checking and adjusting the chain lubrication

m CAUTION!

• Never work without chain lubrication! If the saw chain runs

dry, the cutting equipment may become irreparably dam-

aged in a short time.

• Always check chain lubrication before starting work.

NOTE

Use only saw chain oil preferably biodegradable. Do not use

waste oil, motor oil, etc.

While working, check whether the chain lubrication is working

correctly.

With the chainsaw running at a medium speed, hold it over a

sawn oﬀ tree stump or a suitable ground sheet. If the lubrication

is adequate, a light ﬁlm of oil will form on the tree stump or the

ground sheet (see ﬁg. F).

• If required, the chain lubrication can be increased or de-

creased using the oil adjusting screw (19).

• To do this, use the supplied ﬂat-head screwdriver (31):

-Press and then turn the oil adjusting screw (19) clockwise

to decrease the chain lubrication.

-Press and then turn the oil adjusting screw (19) anticlock-

wise to increase the chain lubrication.

Checking the chain brake

m WARNING!

You must check the chain brake before every use.

The chain brake stops the saw chain in the event of a kickback.

• Make sure that the front hand guard (1) is free of dirt and

moves freely.

• Start the chain saw and accelerate the saw chain to full

speed.

• With the saw chain running, press the front hand guard (1).

The chain brake must slow down and lock the saw chain at

maximum speed.

m WARNING!

High engine revs over a long period with the engine brake

engaged will damage the engine and the chain drive.

If the saw chain (17) moves anyway, contact Customer Service.

10 Basic working procedures when fell-

ing trees

m WARNING!

Risk of injury!

Sawing and felling work as well as all associated tasks may

only be carried out by properly trained operators.

NOTE

Note your country’s laws regarding felling work and contact

the appropriate authority for more information.

• Make sure that no one can be injured by falling branches

and trees.

• Only the required personnel should be in the working area.

• Keep the area around the trunk free and tidy to ensure se-

cure footing for the operators.

• Keep all escape routes free and tidy to ensure that the work-

ing area can be evacuated quickly.

• Do not carry out any felling work in strong wind, poor weath-

er or bad visibility.

• Keep a distance of at least 2½ tree lengths from next work-

ing area.

Use and handling

• Never start the appliance before the guide rail (16), saw

chain (17) and sprocket cover (22) have been ﬁtted cor-

rectly.

• Do not cut any wood that is lying on the ground and do not

attempt to saw roots that are protruding from the soil. Never

immerse the saw chain (17) in the soil, as this could blunt the

saw chain (17).

• If the appliance accidentally comes into contact with a solid

object, turn oﬀ the engine immediately and inspect the appli-

ance for damage.

• Service the appliance carefully. Check for misalignment or

binding of moving parts, breakage of parts and any other

damage that may impair the tool’s operation. If damaged,

have the appliance repaired before use. Many accidents are

caused by poorly maintained tools.

• Keep cutting tools sharp and clean. Properly maintained cut-

ting tools with sharp cutting edges are less likely to bind and

are easier to control.

• Have the appliance checked by qualiﬁed specialists. Use

only the replacement parts recommended by the manufac-

turer.

Preparing the kerf (ﬁg. G)

NOTE

The kerf determines the direction that the tree will fall in.

Place the kerf at right angles to the fall direction.

Saw as close the ground as possible.

Support the chainsaw using the bumper spike (15).

• Start with the ﬁrst kerf cut A. The depth of the kerf should

be about 1/4 of the diameter of the tree and at an angle

of 45°–60°.

• Make the felling cut B around 2–3 centimetres higher than

the horizontal kerf cut A. Ensure that the felling cut B is per-

fectly horizontal.

• Leave around 1/10 of the tree diameter, the hinge C, in front

of the felling cut B. The hinge C guides the tree to the ground

– like a door hinge – and prevents premature falling.

m WARNING!

Risk of accidents!

Do not saw the hinge C at the same time as the felling cut B,

otherwise the tree could fall in an unexpected direction!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PBKS 53 A1 - IAN 315116 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info