Bedienungsanleitung Parkside PDEXS 125 A1 - AN 304779 (Seite 11 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

679415

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

PDEXS 125 A1

■ 8

│

Switching on and oﬀ

NOTE

►

Always switch on the air sander before

bringing it into contact with the workpiece

material.

Switching on the air sander:

♦ Press the operator’s lever fully down

♦ Set the speed using the speed control .

Switching oﬀ the air sander:

♦ Release the operator’s lever .

♦ After you ﬁnish work, disconnect the device

from the compressed air source.

NOTE

►

First disconnect the hose from the compressed

air source (compressor) and only then discon-

nect the compressed air supply hose from the

device. This will ensure that the compressed

air supply hose does not wave around in an

uncontrolled manner.

Advice on use

■ Wait until the device has come to a standstill

before you put it down.

Sanding surfaces

■ Switch the air sander on and bring the whole

of its sanding area into contact with the surface

to be abraded. Move it using even pressure to

and fro over the workpiece.

NOTE

►

The sanding output and appearance are

largely dependent on the choice of sanding

sheet and the pressure applied. A sanding

sheet must be free of defects to produce a

good sanding output.

■ Ensure that you use an even pressure. Excessive

pressure does not produce a higher sanding

output, it just increases the wear on the sanding

sheet.

■ A sanding sheet previously used on metal must

not be used on other materials.

Replacing the backing plate

WARNING! RISK OF INJURY!

► Always disconnect the device from the com-

pressed air source before you replace the

backing plate

♦ Push the open-ended spanner between the

backing plate and collar .

♦ Release the backing plate by turning the pla-

te anticlockwise and holding the open-ended

spanner still against this movement.

♦ Screw on a new backing plate clockwise

until tight while holding the open-ended spanner

still against this movement.

Maintenance and cleaning

WARNING! RISK OF INJURY!

Disconnect the appliance from the

compressed air supply.

CAUTION!

► Before maintenance, clean oﬀ any hazardous

substances that may (due to working pro-

cesses) have accumulated on the appliance.

Avoid all skin contact with these substances.

If the skin comes into contact with hazardous

dusts, this can lead to severe dermatitis. If

dust is produced or swirled up during mainte-

nance, it can be inhaled.

NOTE

To ensure correct functioning and long-term

durability of the sander, pay attention to the

following points:

■ Suﬃcient and continuously intact oil lubrication

is highly important for optimum functioning.

■ Check the speed and vibration levels after each

use.

■ Check the idle speed regularly and after any

maintenance is performed:

use a rev counter and perform the measurement

without any clamped tools. The idle speed may

not be exceeded under any circumstances at a

residual pressure of 6.3 bar.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PDEXS 125 A1 - AN 304779 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info