Bedienungsanleitung Parkside PDEXS 150 A1 - IAN 64578 (Seite 33 von 45) (Englisch, Portugiesisch, Spanisch)

595404

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

33 GB/MT

Before use

Selecting the Grinding Disc

Metal Removal and Surface:

The rate of metal removal and the surface quality

are determined by the grain size of the grinding disc.

lease note that corresponding grinding discs

with diﬀerent grain sizes should be used for

processing diﬀerent materials.

Changing sanding sheets

The air sander is ﬁtted with a hook and loop fastening,

which allows for quick and easy replacement of

sanding discs.

Lift the grinding disc at the side and pull it oﬀ

from the backing pad

in order to remove it.

Note: Before securing a new sanding sheet, re-

move all dust and dirt from the sander plate

Ensure that the openings in the sanding sheet

concur with the boreholes of the sanding plate

Dust / Swarf Removal by Suction

Please note the “Safety instructions” section.

Using the internal vacuum extraction

with dust collection device (see Fig. B):

Push the exhaust air hose

fully on to the

connection for dust extraction

. Put the open-

ing of the dust bag

over the free end of the

exhaust air hose

and fasten the dust bag

ﬁrmly in position.

Note: Empty the dust bag

in good time and

regularly to ensure optimum dust extraction. To

do this open the zip fastener on the underside

of the dust bag

Topping up the oil

In order for the air sander to have a long service life,

there must always be enough pneumatic oil in the

device.

You may ensure this in any of the

following ways:

Connect a service unit with an oiler to the

compressor.

Install a line oiler in the compressed air line or

at the compressed air device.

Put approx. 3–5 drops of pneumatic oil by

hand into the plug nipple

every 15 minutes

of operation.

Preparing for use

Connecting the compressed

air source

Note: The air sander must be operated using

cleaned and condensate-free compressed air only

and its maximum allowable working

pressure of

6.3 bar at the device must not be exceed

ed.

Note: The compressed air source must be ﬁtted

with

a (ﬁlter) pressure reducer so that the air pressure can

be regulated.

Connect the plug nipple

by a quick-release

coupler to the compressed air supply.

Switching on and oﬀ

Note: Always switch on the air sander before

bringing it into contact with the workpiece material.

Switching on the air sander:

Press the operator’s lever

fully down

(see Fig. C).

Set the speed using the speed control

Switching off the air sander:

Release the operator’s lever

After you ﬁnish work, disconnect the device

from the compressed air source.

Note: First disconnect the hose from the com-

pressed air source (compressor) and only then

disconnect the compressed air supply hose

from the device. This will ensure that the com-

pressed air supply hose does not wave around

in an uncontrolled manner.

Before use / Preparing for use

64578_par_Druckluft-Exzenterschleifer_content_LB5.indd 33 27.06.11 16:21

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PDEXS 150 A1 - IAN 64578 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PDEXS 150 A1 - IAN 64578

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info