Bedienungsanleitung Parkside PDEXS 150 A1 - IAN 96905 (Seite 36 von 39) (Deutsch, Englisch, Holländisch)

595405

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

36 GB

extraction. To do so, open the hook-and-loop

fastener at the side of the dust bag

Adding oil

To ensure a long service life for the compressed air

orbital sander the unit must always be adequately

ﬁlled with pneumatic oil.

You may ensure this in any of the follow-

ing ways:

Connect a service unit with an oiler to the

compressor.

Install a compressed air oiler in the air line or

to the compressor.

Manually add approx. 3-5 drops of pneumatic

oil to the plug nipple

every 15 operating

minutes.

Initial use

Connecting the compressed

air source

Note: Only operate the compressed air orbital

sander with cleaned, condensate-free compressed

air. Never exceed the unit‘s maximum operating

pressure of 7.5 bar.

Note: The compressed air source must be ﬁtted

with a (ﬁlter) / pressure reducer to allow the air

pressure to be regulated.

Switching on and oﬀ

Note: Always switch on the compressed air orbit-

al sander before bringing it into contact with the

work piece.

Switching on the compressed air orbital

sander:

Press the operating lever

all the way down

(see Fig. C).

Adjust the speed with the speed control

Switching off the compressed air orbital

sander:

Release the control lever

Disconnect the unit from the compressed air

source after ﬁnishing the work.

Note: First disconnect the hose from the

compressed air source (compressor), only then

disconnect the supply hose from the unit. This

will ensure that the compressed air supply hose

does not wave around or recoil in an uncon-

trolled manner.

Working instructions

Wait until the device has come to a standstill

before you put it down.

Sanding surfaces

Switch on the compressed air orbital sander,

place the entire sanding surface on the surface

to be worked and move it across the work

piece with moderate pressure (see Fig. D).

Note: The sanding output and pattern greatly

dependent on the sanding disc selected and

the pressure applied. Only grinding discs that

are in perfect condition will provide good

grinding performance.

Be sure to apply pressure evenly to increase

the life of the sanding discs.

A sanding sheet previously used on metal must

not be used on other materials.

Replacing the backing plate

RISK OF INJURY! Always

disconnect the device from the compressed air

source before you replace the backing plate

Push the open-ended spanner

between the

backing plate

and collar

Release the backing plate

by turning the

plate anticlockwise and holding the open-ended

spanner

still against this movement.

Working … / Cleaning / Information about warranty and service processing

Before Initial Use / Initial use / Working instructions

96905_par_Druckluft_Exzenterschleifer_content_DE_AT_NL.indd 36 30.04.14 15:46

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PDEXS 150 A1 - IAN 96905 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PDEXS 150 A1 - IAN 96905

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info