Bedienungsanleitung Parkside PDOS 200 A1 IAN 56956 (Seite 34 von 46) (Englisch, Portugiesisch, Spanisch)

744067

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

34 GB/MT

four mounting holes

and suitable ﬁxings

(not supplied). Refer to Figure C.

Positioning the workpiece / tool

rests and eye guard mounts

To ensure safe working, the workpiece / tool rests

the eye guards

and the eye guard mounts

must be correctly positioned.

Check and correct the settings at frequent intervals

to ensure even wear on the grinding wheels

Adjusting the workpiece / tool rests:

1) To adjust the setting, ﬁrst loosen the adjuster

screw

2) Bring the workpiece / tool rest

close up to

the grinding wheel

, the distance between

the grinding wheel

and the workpiece /

tool rest

must be no more than 2 mm.

3) Retighten the adjuster screw

and check

using your hand that the grinding wheel

movement is true and free.

Adjusting the eye guard mounts:

1) To adjust the setting, ﬁrst loosen the fastening

screw

2) Bring the eye guard mount

close up to the

grinding wheel

, the distance between the

grinding wheel

and the eye guard mount

must be no more than 2 mm.

3) Retighten the fastening screw

and check

using your hand that the grinding wheel

movement is true and free. A worn out grinding

wheel

needs to be replaced. This is necessary

when the speciﬁed gap cannot be achieved even

after readjusting the positions of the workpiece /

tool rest

and / or the eye guard mount

Preparing for ﬁrst use

Switching on and oﬀ

Switching on:

j Press the ON / OFF switch

into the “1“

position to switch the device on and run it

at a constant speed.

Switching off:

j Press the ON / OFF switch

into the “0“

position to switch the device oﬀ.

Grinding a workpiece

NOTE: Use the ﬁne grinding wheel for precise

grinding tasks (grade “A80M”).

NOTE: Use the coarse grinding wheel for rough

grinding tasks (grade “A36M”).

j Switch on the machine as described above.

j To grind metal tools or metal items, place the

workpiece on the workpiece / tool rest

and

slowly bring it up to the grinding wheel

j Press the workpiece carefully against the grind-

ing wheel

. Pressing too hard can overload

the device. When grinding always use the

circumferential end face (not the sides) of the

grinding wheel only (See Figures D, E, F).

Replacing a grinding wheel

WARNING!

RISK OF INJURY!

Before

carrying out any tasks on the device itself and

when you are not using the device, always pull the

mains plug out of the mains socket.

J Do not use damaged grinding wheels.

J Only use grinding wheels with details that cor-

respond with those given on the device rating

plate. The circumferential speed should be

equal to or greater than the value given on the

device rating plate.

j Only grinding wheels with markings indicating

the manufacturer, the type of adhesive, dimen-

sions and permitted circumferential speed are

to be used. If you install new grinding wheels

carry out a ringing test before use. Grinding

wheels in good condition give a clear ringing

noise when struck lightly with a plastic hammer.

1) Take oﬀ the outer part of the wheel guard cov-

by unscrewing the 3 threaded ﬁxings

(see Figs. N, O).

Before use / Preparing for first use

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PDOS 200 A1 IAN 56956 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PDOS 200 A1 IAN 56956

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info