Bedienungsanleitung Parkside PDSS 310 A1 - IAN 96878 (Seite 13 von 94) (Dänisch, Französisch, Schwedisch, Finnisch)

595413

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

13 GB/IE

After initial use / Maintenance / Cleaning and Care / Troubleshooting

Commissioning

After initial use

Once the task has been ﬁnished the device must be

disconnect from the compressed air supply

Brieﬂy activate the trigger

of the equipment

to release any residual compressed air.

Now pull back the safety on the connection

coupling of your compressed air hose.

Now remove the hose from the plug nipple

Careful when putting the

device down. Always put down the device so it

does not rest on the trigger. This could potenti-

ally result in inadvertent activation of the tool,

which in turn could result in hazards.

Maintenance

ATTENTION! All maintenance must be per-

formed by trained individuals. Follow the speciﬁed

maintenance instructions to ensure a long life and

proper operation of this quality product.

Disconnect equipment from the compressed air

source when performing maintenance and care.

Check the condition of wear and tear items

and accessories with each maintenance.

Note: Daily cleaning and regular lubrication

are an absolute necessity for smooth operation.

Only use special tool oil with a high viscosity

(thin ﬂuid). Oil for compressed air tools or

SAE10-20 motor oil are suitable.

ATTENTION! Do not use other (especially

high viscosity) lubricants. Malfunctions or per-

manent damage may otherwise occur.

The following lubricating options are

available:

a) via the lubricator

Fill the lubricator included

with a bit of oil

by ﬁrst unscrewing the inlet screw from the lu-

bricator.

Now install the lubricator

in the compressed

air supply as described in chapter „Establishing

connections”.

b) via oil-mist generator

If a complete maintenance unit with oil-mist

generator is installed on your compressor the

lubricator

does not necessarily need to be

mounted.

To use the oil-mist generator plug the plug

nipple

directly into the equipment and con-

nect with your air hose.

c) by hand

Alternatively you can also manually lubricate

your equipment (not recommended).

To do so, remove the screw plug on the oil ﬁller

port.

Apply 3–5 drops of oil to the compressed air

connection and the oil ﬁlling port before using

the compressed air tool

If the air tool has not been used for several

days 5–10 drops of oil must be added to the

air connection

and the oil ﬁller port

Note: Regular lubrication is imperative to ensure

the longest possible life for your compressed air de-

vice. We recommend continuous lubrication via the

included lubricator

Always store your air tools / equipment in dry

locations.

No maintenance is required beyond the above

lubrication and cleaning.

Cleaning and Care

Only clean the tool with a dry cloth.

Never clean with ﬂuids such as petrol, solvents

or water.

Do not allow liquids to enter the equipment.

Troubleshooting

Note: Regular lubrication is imperative to ensure

the longest possible life for your compressed air de-

vice. We recommend continuous lubrication via the

included lubricator

After every maintenance verify the equipment

is still operating as originally.

96878_par_Druckluft-Schlagschrauber PDSS 310 A1_content_GB_IE_FI_SE_DK_BE.indd 13 23.04.14 15:54

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PDSS 310 A1 - IAN 96878 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PDSS 310 A1 - IAN 96878

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info