Bedienungsanleitung Parkside PDT 40 C2 - IAN 96899 (Seite 25 von 28) (Deutsch, Englisch, Holländisch)

595417

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

25 GB

Preparing the product for use / Operation

Connect the device to a suitable compressed

air source.

1. To do so, press the compressed air hose quick-

release coupling (not included in the scope of

delivery) on the ¼” threaded nipple

of the

compressed air tacker.

Locking is automatic.

2. Connect the other end of the compressed air

hose to the (ﬁlter) pressure reducer on the com-

pressor.

Loading the magazine

1. Press the magazine lever

and pull the mag-

azine cover back to its stop position.

2. Insert the corresponding fastener (nails, see

Fig. 01 or staples, see Fig. 02) into the maga-

zine

. The tacks must be put on the rail of

the magazine

3. Slide the magazine cover forwards until it locks.

Operation

Load the magazine

of the compressed air

tacker as described in the chapter “Loading the

magazine“.

Use the pressure reducer to set the correct

operating pressure.

Ensure that the permissible operating pressure

of 8 bar at the device is never exceeded.

Operating pressure that is too high does not

provide any performance increase, but only in-

creases compressed air consumption and ac-

celerates wear on the device.

Switch on the compressor.

Allow the compressor to run once long enough

until maximum tank pressure is reached and the

device is switched oﬀ.

Place the compressed air tacker on the workpiece

and press the trigger

NOTE: The compressed air tacker

is equipped with a trigger lock

The fastener will only

leave the device

when the mouth of the compressed air tacker is

pressed against the workpiece and the trigger

is actuated.

Check that the fastener has been driven in cor-

responding to the work requirements.

– If the fastener is protruding, increase the air

pressure in 0.5 bar increments.

– If the fastener is too deep, decrease the air

pressure in 0.5 bar increments.

As an alternative, you can accelerate the work

by keeping the trigger

depressed.

Set the compressed air tacker against the work-

piece.

Press the device against the workpiece until the

mouth

touches it. The fastener will leave the

device.

As long as the trigger

is kept depressed, each

time the mouth

touches the workpiece one

fastener will leave the device.

Another alternative is to keep the mouth

pressed against the workpiece.

Each time the trigger

is actuated, a fastener

will leave the device.

NOTE: Fine adjustment with the knurled screw

is possible.

Turn the knurled screw

downwards in order

to drive the fastener more deeply into the work-

piece.

Turn the knurled screw

upwards in order to

drive the fastener less deeply into the workpiece.

Safety of the fastener driving tool / Preparing the product for use

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PDT 40 C2 - IAN 96899 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PDT 40 C2 - IAN 96899

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info