Bedienungsanleitung Parkside PDT 40 C2 - IAN 96899 (Seite 26 von 28) (Französisch)

595417

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

26 GB

… / Disposal / Translation of the original declaration of conformity / ManufacturerOperation / Maintenance and cleaning / Service / Warranty

Turn the exhaust air aperture

to guide the

exhaust airﬂow in the desired direction.

After ﬁnishing work, disconnect the device from

the compressor.

Removing jammed fasteners

If a staple or nail gets jammed in the magazine

slot, immediately disconnect the compressed

air supply.

Open the magazine

as described in the

chapter “Loading the magazine“.

Open the face plate

by pulling the face

plate quick clamping lever

in the direction

of the trigger lock

Remove the jammed fastener.

Close the face plate

by pulling the face

plate quick clamping lever

in the direction

of the exhaust air aperture

Close the magazine

of the compressed air

tacker as described in the chapter “Loading the

magazine“.

Maintenance and cleaning

RISK OF INJURY! Be absolutely certain to

disconnect the device from the compressed air

source before cleaning or maintaining it.

Maintenance

Lubrication with oil mister

NOTE: As a treatment stage after the pressure re-

ducer, an oil mister provides continuous and opti

mum

lubrication of the compressed air tacker. An oil mis-

ter gives oﬀ ﬁne drops of oil into the airﬂow and so

guarantees regular lubrication.

Install the oil mister after the (ﬁlter) pressure re-

ducer. To do so, insert the nipple of the oil mister

into the quick-release coupling of the (ﬁlter)

pressure reducer.

Then connect the compressed air device to the

quick-release coupling provided for it.

Manual lubrication

NOTE: If you do not have an oil mister, lubricate the

device each time after driving about 5000 fasteners.

Apply 1–2 drops of special compressed air oil

into the threaded nipple

of the compressed

air tacker.

Then press the trigger

several times.

ATTENTION: Be certain not to use too much

oil; otherwise oil could leave the mouth with the

fastener and potentially damage the workpiece.

Cleaning

Do not use any sharp objects to clean the device.

Do not allow any liquids to enter the device.

Otherwise the device could be damaged.

Clean the device regularly, preferably always

immediately after ﬁnishing work.

Use a dry cloth to clean the housing. Under no

circumstances should you use petrol, solvent or

cleaners which attack plastic.

After each use, pack the compressed air tacker

in the carrying case it was delivered with to

protect it from dirt.

Service

Have your fastener

driving tool repaired only by qualified

specialist personnel using original man-

ufacturer parts only. This will ensure that

your fastener driving tool remains safe to use.

Note: Spare parts not listed (e.g. carbon brushes,

switches) can be ordered through our call centre.

Warranty

The warranty for this appliance is for 3

years from the date of purchase. The ap-

pliance has been manufactured with care

and meticulously examined before deliv-

ery. Please retain your receipt as proof

of purchase. In the event of a warranty

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PDT 40 C2 - IAN 96899 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PDT 40 C2 - IAN 96899

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info