Bedienungsanleitung Parkside PEH 30 A1 - IAN 93528 (Seite 31 von 34) (Französisch)

595292

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

31 GB

Preparing for useGeneral safety advice for electrical power tools / Preparing for use

The planing process

CAUTION! DANGER OF KICKBACK!

Always switch on the device before placing it

against the workpiece.

Set the required cutting depth.

Switch on the device.

Always place the front part of the sole

down

ﬁrst on to the workpiece.

Guide the device with even forward movement

over the surface being planed.

Move the device forward at a slow rate and

ensure that the contact pressure acts evenly on

the sole

. Moving forward at too great a rate

results in a poorer surface quality and can lead

to blocking of the planing debris removal port.

Chamfering edges (see Fig. H)

The V-grooves

in the front sole

allow the de

vice

to be used for simple chamfering of workpiece edges.

Use the V-groove most appropriate to your

desired chamfer width.

Place the planer with the V-groove

on the

work-

piece edge and guide the planer along the edge.

Using the guide fence (see Fig. I)

Attach the guide fence

to the device with

the ﬁxing screw

Release the ﬁxing nut

and set the guide at

the desired distance.

Retighten the ﬁxing nut

Exert some slight sideways pressure when guid-

ing the planer with the guide fence.

Using the rebate depth stop

(see Fig. J)

Attach the rebate depth stop

to the device

with the ﬁxing screw

Set the desired rebate depth with the rebate

depth stop

Make the required number of passes with the

planer until desired rebate depth is achieved.

Removing and installing a

planer blade

(see Fig. D + E)

DANGER OF INJURY!

Before you carry out any work on the device always

pull the mains plug out of the mains socket.

CAUTION! The sharp cutting edges of the plan-

er blade

present an injury hazard! Never

touch the cutting edges of the planer blade

The planer blade

has two cutting edges and it

can be ﬁtted either way around.

Replace the planer blade

when both cutting

edges are blunt.

Do not resharpen the planer blades

Reversing or replacing a planer blade

IMPORTANT INFORMATION:

Do not release the two Allen keys. They are used to

adjust the height of the blade shaft.

Adjustment is necessary only if you wish to use a

diﬀerent planer blade type e.g. a proﬁled blade.

Always replace both blades at the same time to

avoid out of balance forces.

NOTE: If you only release one blade ﬁrst then you

can use the factory-ﬁtted second blade for orientation

when you ﬁt the new blade.

1. Release the 3 bolts of the cutting element

using the supplied open spanner

Press the removable side guard

into the slot

in the housing.

2. Push the cutting element

sideways out from

the blade shaft

3. Push the planer blade

sideways out from

the cutting element

4. Reassembly is carried out in the reverse order

with a reversed or new planer blade.

5. Planer blades

can be obtained from the

service address indicated (see section about

warranty).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PEH 30 A1 - IAN 93528 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PEH 30 A1 - IAN 93528

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info