Bedienungsanleitung Parkside PFBS 9.6 A1 - IAN 78443 (Seite 54 von 60) (Deutsch, Englisch, Holländisch, Französisch)

634192

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

54 GB

General safety advice for electrical power toolsGeneral safety advice for electrical power tools

Special safety advice relating

to grinding and disc-cutting

a) Always use the guard designed for

the type of abrasive consumable you

are using. Always use abrasive con-

sumables approved for use with your

electrical power tool. Abrasive consuma-

bles not approved for use with your electrical

power tool cannot be adequately guarded

and are unsafe.

b) To ensure the highest level of opera-

tional safety, the disc guard cover

must be attached to the electrical

power tool and set in such a way that

the smallest possible area of the

abrasive consumable is exposed to

the operator. The disc guard cover is there

to protect the operator from pieces breaking

oﬀ and accidental contact with the abrasive

consumable.

c) Abrasive consumables must be used

only for their recommended purpos-

es, For example: never grind with the

side face of a cutting disc. Cutting discs

are intended for removing material using the

edge of the disc. Sideways forces on these

abrasive consumables can cause them to break.

d) Always use an undamaged mounting

flange of the correct size and shape

for your selected grinding disc. Suitable

ﬂanges support the grinding disc and reduce

the chance of it breaking. Flanges for cutting

discs are diﬀerent from the ﬂanges for other

abrasive discs.

e) Never use worn down abrasive con-

sumables intended for larger electrical

power tools. Abrasive consumables intended

for larger electrical power tools are not designed

for the faster rotational speeds of these smaller

electrical power tools and could break.

Further special safety

advice for disc-cutting

a) Avoid snagging the cutting disc and

do not use too much contact pressure.

Do not attempt to make excessively

deep cuts. Overloading the cutting disc in-

creases the load and the tendency of the disc

to twist or snag in the cut, making kickback or

disc breakage more likely.

b) Avoid the area in front of or behind

the rotating cutting disc. If the cutting disc

is moving away from you at the point of con-

straint in the workpiece, then, in the event of

a kickback, the electrical power tool and the

rotating disc may be thrown towards you.

c) If the cutting disc jams or you stop

work for a while, switch the device

off and hold it until the disc comes to

a complete stop. Never attempt to

pull the still rotating cutting disc out of

the cut as this could cause kickback.

Determine and rectify the reason for the jamming.

d) Do not switch on the device if the cut-

ting disc is in the workpiece. Allow

the cutting disc to reach full speed be-

fore carefully continuing with the cut.

Otherwise the disc could snag, jump out of the

workpiece or cause a kickback.

e) Support boards or workpieces whilst

cutting to reduce the risk of kickback

caused by a jammed cutting disc. Large

workpieces may bend under their own weight.

The workpiece must be supported to both sides

of the cutting disc and particularly near the

cutting disc and at the workpiece edge.

f) B

e particularly careful when pocket

cutting in existing walls or other areas

where you cannot see what you are cut-

ing into. The cutting disc plunged into the surface

could cut through gas or water pipes, electricity

cables or other objects and cause kickback.

Special safety advice for

abrading using sandpaper

Do not use over-sized sanding sheets.

Follow the manufacturer’s recommen-

dations for sanding sheet size. Sanding

sheets that project beyond the backing pad

could cause injury in addition to jamming,

tearing of the sheet or kickback.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PFBS 9.6 A1 - IAN 78443 Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info