Bedienungsanleitung Parkside PFMR 1400 C2 - IAN 273041 (Seite 6 von 37) (Deutsch, Englisch, Holländisch, Französisch)

679450

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

6 GB/IE

Introduction

Paint & mortar mixer

PFMR 1400 C2

Introduction

Congratulations on your purchase. You have selec-

ted a high quality product. The instructions for use

are a part of this product. They contain important

information about safety, use and disposal. Before

using the product, please familiarise yourself with all

the operating and safety instructions. When passing

this product on to others please be sure to also in-

clude all of its documentation.

Intended use

The machine is intended for mixing building materi-

als that are in a ﬂuid or powder form, e.g. paint,

mortar, adhesives, plaster and similar substances.

Depending on the consistency of the material and

the amount to be mixed, the appropriate agitator

with the suitable mixing eﬀect should be used. The

machine may only be utilised for its intended use.

Any other use is not intended. The user / operator,

not the manufacturer, is liable for resulting damages

or any type of injury resulting from any other use that

is not intended. Please note that our devices were

not constructed for commercial, manual, or industrial

use. We do not accept any warranty liability if the

device is used for commercial, manual, or industrial

operations, or activities similiar to these.

Features

Handle

Open-end spanner for changing agitator

Support bracket

Agitator shaft with M-14 inner threading

ON / OFF switch

Hold-to-run button

Mixing paddle

7 a

Mixing spiral

7 b

Shaft

Scope of delivery

1 Paint & mortar mixer PFMR 1400 C2

1 Mixing paddle

2 Open-end spanners for changing agitator

1 Support bracket

4 Crosshead screws

1 Instructions for use

Technical Data

Mains voltage: 230 V∼ 50 Hz

Power input: 1400 W

Idle speed: 0–700 min

-1

Mixer holder: M14

Protection class: II /

Weight without

mixing paddle: 3590 g

Noise and vibration data:

Values for noise determined in accordance with

EN 60745. The A-weighted noise levels of the

electrical power tool are typically:

Sound pressure level: 92.5 dB(A)

Sound power level: 103.5 dB(A)

Instability K: 3 dB

Wear hearing protection!

The total vibration (vector sum of three directions) is

calculated in accordance with EN 60745:

Front Handle: a

: 3.93 m / s

Rear Handle: a

: 8.33 m / s

Uncertainty K = 1.5 m / s

The vibration level speciﬁed in

these instructions was measured in accordance with

an EN 60745 standardised measurement process

and can be used to compare equipment. The vibra-

tion emission value speciﬁed can also serve as a

preliminary assessment of the exposure.

The vibration level will change according to the ap-

plication of the electrical tool and in some cases,

may exceed the value speciﬁed in these instructions.

Regularly using the electric tool in such a way may

make it easy to underestimate the vibration.

Introduction / General power tool safety warnings

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PFMR 1400 C2 - IAN 273041 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info