Bedienungsanleitung Parkside PFS 100 C3 - IAN 97735 (Seite 29 von 33) (Französisch)

576717

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

29 GB

General safety advice for electrical power tools / Advice on useGeneral safety advice for electrical power tools

Precise observation of the hazard

warnings, information and data sheets

available from the sprayed medium

manufacturer is essential.

Wear a breathing / dust mask! The inha-

lation of paint mist and solvent vapour is haz-

ardous to health.

Work in adequately ventilated spaces

only.

Wear protective glasses!

Never aim the spray at living creatures.

DANGER OF EXPLOSION! Do not use the

device in environments containing gases, open

ﬂames, ﬁres or gas-operated water heaters.

NO SMOKING!

Paint and solvents (thinners) must

have a flashpoint above 21°C.

Advice on use

DIN-sec / Viscosity

The Parkside paint spray gun PFS 100 C3 can be

used to apply sprayed media with a viscosity up to

80 DIN-sec. Viscosity is determined in a simpliﬁed

measuring procedure using the supplied measuring

cup (see Fig. C).

1. Immerse and ﬁll the supplied measuring cup

to the top with the medium to be sprayed.

2. Lift the measuring cup

out of the medium

to be sprayed and let the liquid ﬂow out (see

Figure C).

3. Measure the time in seconds it takes for the

ﬂow of liquid out of the measuring cup to cease.

This time is the “DIN-seconds (DIN-s)” value of

viscosity.

4. If the value is too high, incrementally add and

mix in small quantities of a thinner compatible

with the medium to be sprayed. Proceed in ac-

cordance with the section about “Preparing the

sprayed medium”.

5. Remeasure the DIN-seconds value.

Repeat this procedure until a value is obtained

that complies with the values in the table.

Preparing the sprayed medium

NOTE: Most paints, varnishes etc. in the shops

are intended to be applied by brush not spray. To

achieve the best spraying result, you should prepare

your paint or varnish etc. in accordance with DIN

guidelines to achieve a suitable viscosity (see table).

Use a suitable thinner to achieve the required

thinning of the medium.

Never exceed the maximum viscosity for the

device. The sprayed medium must not be too

thick for the spraying process, otherwise it

could clog up the device.

Ensure that the sprayed medium and the thinner

are compatible with one another. If the wrong

thinner is used, it can lead to lumps forming

which may clog up the device. Never mix nitro-

thinners with synthetic resin paint.

Consult the sprayed medium manufacturer’s

documentation for information about suitable

thinners (water, solvents).

1. Thoroughly mix the unthinned sprayed medium

and bring it to average room temperature

(20–22 °C).

Do not increase the temperature to change the

viscosity.

2. Add a suitable thinner.

3. Test the viscosity as described above (see Fig. C).

NOTE: Never use nitro-thinners to thin synthetic

resin paint!

Example of

material

DIN guidance

value

Car body paint 16-20 DIN-sec

Acrylic paint 25-30 DIN-sec

Synthetic resin paint 25-30 DIN-sec

Primer 25-30 DIN-sec

Wood impregnation 25-30 DIN-sec

Glaze 25-30 DIN-sec

Hammer finish paint 30-35 DIN-sec*

Emulsion paint 40-80 DIN-sec

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PFS 100 C3 - IAN 97735 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PFS 100 C3 - IAN 97735

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info