Bedienungsanleitung Parkside PFS 400 A1 - IAN 307721 (Seite 8 von 38) (Englisch)

679220

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

PFS 400 A1

│

5 ■

5. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replace-

ment parts. This will ensure that the safety of

the power tool is maintained.

Additional safety instructions for

paint spray guns

■ Keep your work area clean, well lit and free

of paint and solvents, cloths and other inﬂam-

mable materials. Possible risk of spontaneous

combustion. Have a fully functioning ﬁre extin-

guisher available at all times.

■ Ensure adequate ventilation in the spray zone

and suﬃcient fresh air in the entire room.

Evaporation of ﬂammable solvents will cause an

explosive environment.

■ Do not spray or clean with materials whose

ignition point is lower than 21°C. Use ma-

terials based on water, non-volatile hydro-

carbons or similar materials. The evaporation

of volatile solvents will cause an explosive

environment.

■ Do not spray near ignition sources such as

static electric sparks, open ﬂames, ignition

ﬂames, hot items, motors, cigarettes or sparks

caused by plugging in/unplugging power

cables or by operating switches. These ignition

sources could ignite a ﬁre in the environment.

■ Do not spray any material if you do not know

whether it is potentially dangerous. Unknown

materials can cause hazardous conditions.

■ Wear additional personal protective equip-

ment such as suitable gloves and a protective

mask/respirator when spraying or handling

chemicals. Wearing appropriate protective

equipment for the conditions reduces your expo-

sure to dangerous substances.

■ Be aware of the potential hazards of the

sprayed material. Take note of the markings

on the container and the manufacturer's infor-

mation on the sprayed material, including the

instructions to use personal protective equip-

ment. The manufacturer's instructions are to

be followed to reduce the risk of ﬁre or injuries

caused by poisons, carcinogens, etc.

■ Do not use the spray gun to spray ﬂammable

substances. Do not clean spray guns with ﬂam-

mable solvents.

WARNING!

► Be aware of any dangers inherent to the

spray material and pay attention to all pack-

aging labels and other information provided

by the producer of the substance.

Working procedures

Viscosity

The appliance can process spray materials up to a

maximum 70 DIN/s. (viscosity). You can deter-

mine the viscosity (thickness) of the substance with

the supplied measuring cup using a simpliﬁed

measuring procedure.

♦ Fill the supplied measuring cup to the brim

with the spray material.

♦ Remove the measuring cup from the spray

material and allow the liquid to run out.

♦ Measure the time (in seconds) until the stream

of liquid stops. The resulting value is referred to

as DIN seconds (DIN-s).

♦ If the value is too high, gradually thin the spray

material by adding small amounts of a suitable

thinning agent in and mixing the liquid.

♦ Measure the DIN seconds again. Repeat the

process until you measure a viscosity of less

than 70 DIN/sec.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PFS 400 A1 - IAN 307721 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PFS 400 A1 - IAN 307721

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info