Bedienungsanleitung Parkside PGS 500 A1 - IAN 303129 (Seite 22 von 88) (Deutsch, Holländisch, Französisch, Portugiesisch, Spanisch)

679462

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

PGS 500 A1

│

19 ■

Additional safety instructions for all

applications

Kickback and corresponding safety instructions

Kickback is a sudden reaction caused when a ro-

tating attachment part, e.g. grinding disc, abrasive

band, wire brush, etc. catches or jams. Catching

or jamming leads to an abrupt stop of the rotating

attachment part. If this happens, an uncontrolled

power tool will turn rapidly against the direction of

rotation of the attachment part.

If, for example, a grinding disc catches or jams, the

edge of the grinding disc that is projecting into the

workpiece can get caught and break oﬀ the grinding

disc or cause a kickback. The grinding disc can then

ﬂy in the direction of the operator or away from him,

depending on the direction of rotation of the disc at

the blockage. This can also break grinding discs.

A kickback is caused by improper or incorrect use

of the power tool. This can be avoided by taking

proper precautions as described below.

a) Hold the power tool ﬁrmly in both hands

and position your body and arms, so that

they can absorb the kickback forces. By

taking adequate precautions, the operator can

stay in control of the kickback forces.

b) Take special care when working around

corners, sharp edges, etc. Avoid allowing

the attachment part to bounce back from

the workpiece or jam in the workpiece. The

rotating attachment part is more likely to jam

on corners or sharp edges or if it bounces back

from them. This can cause a loss of control or

kickback.

c) Do not use toothed saw blades. Such attach-

ment parts often cause a kickback or loss of

control over the power tool.

d) Always move the attachment part in the

material in the same direction as the direc-

tion in which the cutting edge leaves the

material (in other words, the same direc-

tion in which the chips are thrown out).

Guiding the power tool in the wrong direction

will cause the cutting edge of the attachment

part to jump out of the workpiece, which can

lead to the attachment part being pulled in this

direction.

e) Always ﬁx the workpiece when using rotary

ﬁles, high-speed milling tools or hard-metal

tools. Even a slight tilting in the groove can

cause these attachment parts to jam and lead

to a kickback. When a rotary ﬁle, high-speed

milling tool or hard-metal milling tool jams,

the accessory tool can jump out of the groove

and lead to loss of control of the power tool.

Supplementary safety instructions

for grinding

Special safety instructions for grinding:

a) Use only the grinding accessories approved

for your power tool and only for the recom-

mended applications. Example: Never grind

with the side surface of a cutting disc. Cutting

discs are designed to remove material with the

edge of the disc. Any lateral application of

force on these grinding tools can lead to break-

age.

b) Use only undamaged mandrels of the correct

size and length and without undercut on the

shoulder for conical and straight pencil grind-

ers. Using an appropriate mandrel reduces the

risk of breakages.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PGS 500 A1 - IAN 303129 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info