Bedienungsanleitung Parkside PHKS 66 - KH 3026 (Seite 14 von 29) (Englisch)

558823

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

14 GB/IE/CY

Preparing for use

Make sure that the cutting speed resulting from the

eﬀects of diﬀerent saw blades, materials and the

force you apply to advance the saw is always less

than the circumferential speed (CS) under no load.



Connecting the vacuum

sawdust extraction device

 Insert the adapter for vacuum sawdust removal

into the sawdust removal connector

 Connect a vacuum device approved for the

extraction of sawdust and splinters (see Fig. A).



Changing a saw blade

WARNING!

Press the spindle lock only after

the mains plug has been pulled out of the socket!

1. Then remove the guide fence

by releasing

the wing screw

2. Set the cutting depth (by means of the wing

screw for cutting depth setting clamp

) to

the minimum position, 0 mm.

3. Swing back the retractable blade guard

with the help of the retracting lever

7 a

and put

the device down.

4. Press the spindle lock button

(until it engages)

and release the clamping screw

using the

Allen key

. Now remove the clamping screw

with integral washer head

and the clamp-

ing ﬂange

(see Fig. D).

5. Detach the saw blade.

6. The installation of a sawblade is done in the

reverse order.

7. Press the spindle lock button

(until it engages)

and tighten the clamping screw

using the

Allen key.

WARNING!

The arrow on the saw blade

must agree with the arrow showing the direction of

rotation (running direction shown on the device).

 Ensure that the saw blade is suitable for the

saw spindle speed.



Installing and setting

the riving knife

WARNING!

The distance between the riving

knife

and the saw blade must not be greater

than 5 mm. If the riving knife has been removed e.g.

for a plunge cut, this distance must be observed

again when the riving knife is reinstalled (see Fig. F).

Removing the riving knife (see Fig. E):

1. Release the wing screws of the cutting depth

setting clamp

and swing the circular saw

up until it meets the stop; this exposes the riving

knife mounting

2. Screw out the mounting screws

and remove

the riving knife

WARNING!

After completion of the plunge

cut the riving knife

must be reinstalled before

the circular saw is used for any other sawing tasks.

Setting the riving knife (see Fig. F):

Set the distance between the riving knife

and

the tips of the saw blade teeth to a maximum of

5 mm, and the distance between the tip of the riving

blade and the lowest point of the saw blade to a

maximum of 5 mm.

The distances to be set are illustrated in Fig. F.



Tips and tricks

 Use the cutting angle scale according to the

cutting angle

12 b

: rectangular cut = 0° mark,

45° cut = 45° mark.

 Breaking out of the cut edges of delicate sur-

faces, e.g. coated chipboard or doors, can be

avoided by applying masking tape in advance

along the cutting line. This has the additional

advantage that masking tape shows up the cut-

ting line better than a smooth surface. An even

more eﬀective way of stopping the cut edges

from being broken out is to clamp a thin piece

of wood along the cutting line, which is then

also sawn through.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PHKS 66 - KH 3026 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PHKS 66 - KH 3026

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info