Bedienungsanleitung Parkside PHLG 2000 B1 - IAN 96232 (Seite 17 von 21) (Deutsch, Englisch)

576734

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

17 GB

Do not work in the vicinity of easily ignitable

gases or materials.

Heating of plastics, paints, varnishes etc. can

lead to the creation of gases that are hazard-

ous to health. Make sure you always have

adequate ventilation.

Let the device cool down completely before

you put it into storage. Always place your

heat gun down on its end, with the nozzle

pointing upwards.

In addition, you should never leave the device

working unattended.

When taking a break from your work, before

carrying out any tasks on the device itself (e.g.

changing the nozzle) or when you are not

using the device, always pull the mains plug

out of the mains socket.

Do not direct the device at the same spot for

too long a period.

Maintain a distance between the jet outlet

nozzle and the workpiece or the surface being

heated. An air blockage could lead to over-

heating of the appliance.

Pay heed to the direct working area and also

to its surroundings. The heat produced could

reach to inﬂammable articles located out of the

visible area.

Always keep the device clean, dry and free

of oil or grease.

Never use the device for a purpose for which it

was not intended.

Operation

Preparing the device for use

CAUTION! When using the device, never

allow the ventilation slots to be covered.

CAUTION! DANGER OF BURNS! Do not

touch the hot nozzle.

Switching on the device:

Press the ON / OFF switch

into setting “I“

or “II“.

Switching off the device:

Press the ON / OFF switch

into setting “0“.

Adjusting the air quantity and temperature:

You can use the temperature and air quantity control

to set two diﬀerent blower levels. It is therefore

possible to select the appropriate quantity of air and

temperature in accordance with the intended use:

Setting I 300 l / min 350 °C

Setting II 500 l / min 550 °C

Use as free-standing unit / during

cooling (see Fig. D):

Always set the device down upright on

a level surface, this will allow

· you to have both hands free

· the device to cool

Changing the nozzle

Too much heat causes paints

and plastics to ignite.

CAUTION! Do not inhale the resulting vapours.

Protector nozzle

– for removing paint

and varnish (see Ill. B):

Place the protector nozzle

on the outlet

tube

The spatula shape of the nozzle ensures the air

is properly directed. Use a separate spatula for

removing paint or varnish.

Flat nozzle

– for detaching glues,

softening paint (see Ill. C):

Place the ﬂat nozzle

on the outlet tube

Do not apply heat for too long a period, as

burnt paint becomes much more diﬃcult to

remove. Many glues can be softened by warm-

ing. Glued connections can then be detached

and excess glue removed.

Reducing nozzle

– for welding plastic:

Place the reducer nozzle

on the

outlet tube

Use the reducing nozzle

for heat-shrinkable

sleeves and ﬁlm.

General safety advice for electrical power tools / OperationGeneral safety advice for electrical power tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PHLG 2000 B1 - IAN 96232 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PHLG 2000 B1 - IAN 96232

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info