Bedienungsanleitung Parkside PISG 120 A2 - IAN 331996 (Seite 37 von 137) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

779750

Zoom out

Zoom in

Vorherige Seite

1/137

Nächste Seite

37GB/IE

Make sure that the ON/OFF switch

is set to position “O” (“OFF”)

or that the power cable

is not

plugged into the socket.

Connect the welding cable

according to its polarity and in

accordance with the speciﬁcations

of the electrode manufacturer.

To do this, connect the connector of

the earth terminal

(black) with the

relevant output on the inverter welder

(black, marked with “-”).

Connect the connector of the

electrode holder

(red) with the

relevant output on the inverter welder

(red, marked with “+”).

Put on appropriate protective

clothing in accordance with the

speciﬁcations and prepare your

workspace.

Connect the earth terminal

to the

workpiece.

Clamp the electrode into the elec-

trode holder

Switch the device on by setting the

ON/OFF switch to the

“I” (“ON”)

position.

Adjust the welding current using the

rotary knob

depending on the

electrode being used.

Note: See the following table for infor-

mation on the welding current to be used,

depending on the electrode diameter.

Ø Electrode Welding current

1.6 mm 40-55 A

2.0 mm 55-65 A

2.5 mm 65-80 A

3.2 mm 80-120 A

Attention: Do not bring the earth

terminal

and the electrode holder

electrodes into direct contact with one

another.

Attention: When welding with

electrodes (MMA – manual metal arc

welding – electrode welding), the

electrodeholder

and the earth

terminal

must be connected in

accordance with the speciﬁcations of

the welding wire to plus (+) or minus (-).

Hold the welding mask

in front

of the face and start the welding

procedure.

To stop the procedure, set the ON/

OFF switch

to “O” (“OFF”)

position.

ATTENTION!

When the thermal sensor is triggered,

the yellow control lamp

lights up.

In this case, it will not be possible to

continue welding. The device will

remain in operation so that the fan can

cool the device. As soon as the device

is ready for operation again, the yellow

control lamp

will switch off automati-

cally. The welding function can now be

used again.

ATTENTION!

Make sure that you do not rub the weld-

ing wire on the workpiece. Doing this

can damage the workpiece and make

it more difﬁcult to ignite the arc. After

the arc is ignited, maintain the correct

gap from the workpiece. The distance

should be appropriate to the diameter

of the welding wire being used. When

welding maintain this gap as accurately

and consistently as possibly. The angle

between the welding wire and the direc-

tion of operation should be between

20° and 30°.

ATTENTION!

The welding clamp and welding wire

must be placed on the insulated bracket

after welding. Wait until the wire is

cooled before removing the welding

slag. To weld an intermittent weld seam

Using the device

331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB8.indb 37331996_Inverter_Schweissgeraet_PISG_120_A2_content_LB8.indb 37 17.12.2019 14:19:0817.12.2019 14:19:08

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PISG 120 A2 - IAN 331996 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info