Bedienungsanleitung Parkside PK0 400 A1 - IAN 73783 (Seite 55 von 62) (Deutsch, Englisch, Holländisch, Französisch)

763019

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

- 55 -

9. Cleaning, maintenance,

storage, ordering spare

parts and transport

 Important!

Pull out the power plug before doing any

cleaning and maintenance work on the

equipment. Risk of injury from electric

shock!

 Important!

Wait until the equipment has cooled

down completely! Risk of burns!

 Important!

Always depressurize the equipment be-

fore carrying out any cleaning and main-

tenance work (see 9.7.1)! Risk of injury!

9.1 Cleaning

• Keep the equipment free of dirt and dust as

far as possible. Wipe the equipment with a

clean cloth or blow it down with compressed

air at low pressure.

• We recommend that you clean the equipment

immediately after you use it.

• Clean the equipment regularly with a damp

cloth and some soft soap. Do not use cleaning

agents or solvents; these may be aggressive

to the plastic parts in the equipment. Ensure

that no water can get into the interior of the

equipment.

• You must disconnect the hose and any

spraying tools from the compressor before

cleaning. Do not clean the compressor with

water, solvents or the like.

9.2 Maintenance work on the pressure

vessel (Figure 1)

Important! To ensure a long service life of the

pressure vessel (7), drain off the condensed water

by opening the drain valve (9) each time after

using. Release the vessel pressure ﬁ rst (see 9.7.1).

Open the drain screw by turning counter-clock-

wise (looking at the screw from the bottom of the

compressor) so that all the condensed water can

run out of the pressure vessel. Then close the drain

screw again (turn it clockwise). Check the pressure

vessel for signs of rust and damage each time

before using. Do not use the compressor with a

damaged or rusty pressure vessel. If you discover

any damage, then please contact the customer

service workshop.

 Important!

The condensed water from the pressure

vessel will contain residual oil. Dispose

of the condensed water in an environ-

mentally compatible manner at a suitable

collection point.

9.3 Safety valve (Figure 3)

The safety valve (19) has been set for the highest

permitted pressure of the pressure vessel. It is

prohibited to adjust the safety valve or remove its

seal. Actuate the safety valve from time to time to

ensure that it works when required. Pull the ring

with sufﬁ cient force until you can hear the com-

pressed air being released. Then release the ring

again.

9.4 Checking the oil level at regular inter-

vals (Figure 11)

Place the compressor on a level and straight sur-

face. The oil level must be between the MAX and

MIN marks on the oil level window (Fig. 18). Oil

change: we recommend SAE 15W 40 or equiva-

lent. The original oil ﬁ lling must be changed after

100 hours in operation; thereafter the oil must be

drained and replaced with new oil after every

500 hours in operation.

9.5 Changing the oil (Figure 1,10, 11)

Switch off the motor and pull the mains plug out

of the socket. After releasing any air pressure (see

9.7.1) you can unscrew the oil drain screw (18)

from the compressor pump (13). To prevent the oil

from running out in an uncontrolled manner, hold

a small metal chute under the opening and collect

the oil in a container. If the oil does not drain out

completely, we recommend tilting the compressor

slightly. When the oil has drained out, reﬁ t the oil

drain screw (18).

Anleitung_4010411_LB2.indb 55Anleitung_4010411_LB2.indb 55 12.03.12 09:5212.03.12 09:52

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PK0 400 A1 - IAN 73783 Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info