Bedienungsanleitung Parkside PKO 400 A1 - IAN 73783 (Seite 54 von 62) (Deutsch, Englisch, Holländisch, Französisch)

668291

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

- 54 -

be checked before putting the equipment into

operation (see 9.4).

7. Assembly and starting

 Important!

You must fully assemble the appliance

before using it for the ﬁ rst time!

You will require the following tools for assembly

and installation:

•

1 x open-ended wrench size 14 mm (not in-

cluded)

•

2 x open-ended wrench size 17 mm (not in-

cluded)

•

1 x open-ended wrench size 23 mm (not in-

cluded)

7.1 Fitting the wheels (11)

Fit the supplied wheels as shown in Figure 5.

7.2 Fitting the supporting feet (8)

Fit the supplied supporting feet as shown in

Figure 6.

7.3 Fitting the air ﬁ lters (15)

Remove the transportation stopper (B) and screw

the air ﬁ lters (15) securely to the equipment (Fig.

7, 8). Make sure that the intake opening on the air

ﬁ lter faces down.

7.4 Changing the transportation cover (A)

Remove the transportation cover from the oil ﬁ ller

opening (21) and insert the supplied oil sealing

plug (16) into the oil ﬁ ller opening. (Fig. 9, 10.)

7.5 Mains connection

•

The compressor is equipped with a mains

cable with shock-proof plug. This can be

connected to any 230V ~ 50 Hz shock-proof

socket which is protected by a 16 A fuse.

•

Before you use the machine, make sure that

the mains voltage is the same as the operating

voltage (see the rating plate).

•

Long supply cables, extensions, cable reels

etc. cause a drop in voltage and can impede

motor start-up.

•

At low temperatures below +5°C, sluggish-

ness may make starting difficult or impossible.

7.6 ON/OFF switch (Fig. 2)

Pull the ON/OFF switch (17) upwards to switch

on the compressor. To switch off the compressor,

press the ON/OFF switch down.

7.7 Setting the pressure (Fig. 1-3)

•

Use the pressure regulator (3) to set the pres-

sure on the pressure gauge (5).

•

Pull the knob of the pressure regulator (3) in

order to release the pressure regulator.

•

Turn the pressure regulator knob to adjust the

pressure. When the required pressure setting is

reached, press the pressure regulator knob.

•

The set pressure can be drawn from the quick-

lock coupling (4).

•

The vessel pressure can be read off the pres-

sure gauge (14).

•

The vessel pressure is drawn from the quick-

lock coupling (20).

7.8 Setting the pressure switch (Fig. 1)

The pressure switch (2) is set at the factory.

Cut-in pressure approx. 6 bar

Cut-out pressure approx. 8 bar

7.9 Overload cut-out (Fig. 3)

The motor of this equipment is protected against

overload by an overload switch (G). If the rated

current is exceeded, the overload switch (G) will

shut down the equipment. After a short cooling

down period, the equipment can be switched on

again by pressing the overload switch (G).

8. Replacing the power cable

If the power cable for this equipment is damaged,

it must be replaced by the manufacturer or its

after-sales service or similarly trained personnel to

avoid danger.

Anleitung_4010411_LB2.indb 54Anleitung_4010411_LB2.indb 54 12.03.12 09:5212.03.12 09:52

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PKO 400 A1 - IAN 73783 Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info